Document
Multilayer Chip Inductors
LL1005-FH
Series
TYPE LL1005-FH Series
Inductance Range: 1.0~100nH (E-12) Temperature Coefficient of L: + 250ppm/°C typical
DIMENSIONS /
Length (mm)
1.0 ± 0.1
Width (mm)
0.5 ± 0.1
Thickness (mm)
0.5 ± 0.1
Electrode width A (mm)
0.25 ± 0.1
• Marking of polarity: Marking is on the upper Surface of the unit.
•
Marking of polarity Marking: Blue Green
L
W
T A
ELECTRICAL CHARACTERISTICS /
• Inductance Range
1.0~100nH (E-12 Series)
• Inductance Tolerance S ; ± 0.3nH (1.0~5.6nH)
J ; ± 5% (6.8~100nH)
K ; ± 10% (3.3~100nH)
• Q (Typ.)
20~34 (at 800MHz)
• Rated Current
150~300mA
• L Temperature
Coefficient (Typ.)
+ 250ppm/°C
• Applicable Temperature
Range
− 40~+ 100°C
PART NUMBERING SYSTEM /
L L 1 0 0 5—F H
Material / Physical Dimensions / TOKO's Type name /
Inductance
Unit is nH and 3 digits are used. The value is indicated as shown below.
Example / 4N7…4.7nH, 27N…27nH
SOLDERING CONDITIONS / Recommended Pattern
c
b ab
• •
• 20 ~ 34 (at 800MHz) • • •
Tolerance / Inductance /
Tolerance for the Inductance
Mark S J K
Tolerance ± 0.3nH ± 5% ± 10%
Pattern Dimensions (unit: mm)
Flow Soldering
Reflow Soldering
a 0.3~0.5
0.3~0.5
b 0.4~0.5
0.3~0.5
c 0.3~0.5
0.3~0.4
Conditions for soldering temperatures are determined as per figures below after prior confirmation that abnormalities are not evident.
Flow Soldering
7s. 230±5°C
80±20°C 2min.
Reflow Soldering
240°C 225°C
20s. 140~170°C
80s. 2min.
Soldering Iron
2s. 250± 10°C
150± 10°C 2min.
Soldering Iron rating:18W
Multilayer Chip Inductors
TYPE LL1005-FH Series
TOKO Part Number
LL1005-FH1N0S LL1005-FH1N2S LL1005-FH1N5S LL1005-FH1N8S LL1005-FH2N2S
LL1005-FH2N7S LL1005-FH3N3 LL1005-FH3N9 LL1005-FH4N7 LL1005-FH5N6
LL1005-FH6N8 LL1005-FH8N2 LL1005-FH10N LL1005-FH12N LL1005-FH15N
LL1005-FH18N LL1005-FH22N LL1005-FH27N LL1005-FH33N LL1005-FH39N
LL1005-FH47N LL1005-FH56N LL1005-FH68N LL1005-FH82N LL1005-FHR10
Inductance (at 100MHz)
L (nH) Tolerance
1.0 S 1.2 S 1.5 S 1.8 S 2.2 S
2.7 S 3.3 S, K 3.9 S, K 4.7 S, K 5.6 S, K
6.8 J, K 8.2 J, K 10.0 J, K 12.0 J, K 15.0 J, K
18.0 J, K 22.0 J, K 27.0 J, K 33.0 J, K 39.0 J, K
47.0 56.0 68.0 82.0 100.0
J, K J, K J, K J, K J, K
Q Typ. (MHz)
100 800
10 28 9 28
10 30 10 28 10 30
10 30 10 30 11 31 10 30 11 31
10 31 12 34 12 32 12 31 11 30
11 29 11 28 12 27 10 25 10 25
9 23 10 20 10 –– 11 –– 13 ––
S.R.F. (MHz) Typ.
13,500 12,000 10,500
9,400 8,700
7,700 6,800 6,300 5,700 5,100
4,550 4,100 3,750 2,950 2,600
2,350 1,950 1,750 1,700 1,650
1,300 1,250 1,150 1,000
900
RDC (Ω) max.
0.10 0.10 0.10 0.10 0.12
0.12 0.15 0.15 0.18 0.20
0.25 0.25 0.30 0.30 0.40
0.50 0.60 0.60 1.50 1.80
2.00 2.00 2.20 2.50 2.50
LL1005-FH
Series
IDC (mA) max.
300 300 300 300 300
300 300 300 300 300
300 300 300 300 300
300 300 300 200 200
200 200 180 150 100
Q'ty/reel (pcs)
10,000 10,000 10,000 10,000 10,000
10,000 10,000 10,000 10,000 10,000
10,000 10,000 10,000 10,000 10,000
10,000 10,000 10,000 10,000 10,000
10,000 10,000 10,000 10,000 10,000
• Impedance Analyzer & Note
• L, Q • S.R.F. • RDC • IDC •(
( ( (
; HP4291A at 100MHz (Test fixture: 16192A)
) : Self-resonance Frequency ; HP8719D
) : DC Resistance
; HP4338B or equivalent
) : Rated Current
) : Inductance Tolerance (S= ± 0.3nH, J= ± 5%, K= ± 10%)
Inductance (nH) Q
EXAMPLES OF CHARACTERISTICS /
1,000
Inductance vs Frequency
100
Part No.
1N5 6N8 27N
Mark
10
1
10
100
1,000
10,000
f (MHz)
50
Part No. Mark
40 1N5
6N8 27N
30
Q vs Frequency
20
10
0 10 100 1,000
f (MHz)
10,000
Multilayer and Chick Film Chip Inductors
TYPE
LL2012 PTL2012 LL1608 PTL1608 LL1005 PTL1005
TAPING SPECIFICATIONS
(1) Chip's placing Chip Inductors are packed into 8mm width, 4 or 2mm pitch plastic or paper tape and enclosed with cover tape.
(2) Carriage hole position A carriage hole position comes to the right-hand side of tape when sealing tape is pulled toward the operator.
Tape Dimensions (Unit: mm)
( mm)
Reel Dimensions (Unit: mm)
( mm)
P=4.0
2
1.5 T1
Label 2
13
8 3.5 1.75 C
60 180
21
A B T2 T3
Type LL2012 LL1608 LL1005 PTL2012 PTL1608 PTL1005
A B C T1
T2
T3
Tape
4 1.5 2.3 0.3 Max. 2.0 1.1 1.9 0.2 Max. 1.3
Plastic
2 0.6 1.1
Max. 1.0
1.5 2.3 4 1.0 1.8
Max. 0.8 Paper
Max. 0.8
2 0.67 1.15
Max. 0.8
9 11.4
Note: Typical dimensions
• Label: Customer's P/N, Q'ty, TOKO P/N, TOKO, INC. •
ELECTRICAL CHARACTERISTICS TEST METHOD
1. INDUCTANCE, Q
• Test Equipment Used
• Impedance Analyzer: HP4291A (LL1005-FH, LL1608-FS, LL2012-FH,
PTL1005-F, PTL1608-F, PTL2012-F)
HP4191A (LL1608-FH)
• Test Fixture: HP16192A (LL1005-FH, LL1608-FS, LL2012-FH)
HP16092A (LL1608-FH)
HP16193A (PTL1005-F, PTL1608-F, PTL2012-F)
• Test Method
• Set measuring frequency read inductance and Q value.
2. RDC (DC Resistance)
• Test Equipment Used
• HP4338B(HP) or equivalent
• Test Method
(1) Place samples in the test terminals.
(2) Push SW. then measure the Value.
* Do not place in or pull out the sample while pushing SW.
Test Circuit
DC RESISTANC.