DatasheetsPDF.com

MB95F478K Dataheets PDF



Part Number MB95F478K
Manufacturers Fujitsu
Logo Fujitsu
Description 8-bit Microcontrollers
Datasheet MB95F478K DatasheetMB95F478K Datasheet (PDF)

FUJITSU SEMICONDUCTOR DATA SHEET DS702-00004-1v0-E 8-bit Microcontrollers CMOS New 8FX MB95410H/470H Series MB95F414H/F414K/F416H/F416K/F418H/F418K MB95F474H/F474K/F476H/F476K/F478H/F478K ■ DESCRIPTION MB95410H/470H is a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of this series contain a variety of peripheral resources. ■ FEATURES • F2MC-8FX CPU core Instruction set optimized for controllers • Multiplication and div.

  MB95F478K   MB95F478K


Document
FUJITSU SEMICONDUCTOR DATA SHEET DS702-00004-1v0-E 8-bit Microcontrollers CMOS New 8FX MB95410H/470H Series MB95F414H/F414K/F416H/F416K/F418H/F418K MB95F474H/F474K/F476H/F476K/F478H/F478K ■ DESCRIPTION MB95410H/470H is a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of this series contain a variety of peripheral resources. ■ FEATURES • F2MC-8FX CPU core Instruction set optimized for controllers • Multiplication and division instructions • 16-bit arithmetic operations • Bit test branch instructions • Bit manipulation instructions, etc. Note: F2MC is the abbreviation of FUJITSU Flexible Microcontroller. • Clock • Selectable main clock source Main OSC clock (up to 16.25 MHz, maximum machine clock frequency: 8.125 MHz) External clock (up to 32.5 MHz, maximum machine clock frequency: 16.25 MHz) Main CR clock (1/8/10/12.5 MHz ±2%, maximum machine clock frequency: 12.5 MHz) Main PLL clock (up to 16.25 MHz, maximum machine clock frequency: 16.25 MHz) • Selectable subclock source Sub-OSC clock (32.768 kHz) External clock (32.768 kHz) Sub-CR clock (Typ: 100 kHz, Min: 50 kHz, Max: 200 kHz) • Timer • 8/16-bit composite timer × 2 channels • 8/16-bit PPG × 2 channels • 16-bit reload timer × 1 channel • Event counter × 1 channel • Time-base timer × 1 channel • Watch prescaler × 1 channel • UART-SIO • Capable of clock-asynchronous (UART) serial data transfer and clock-synchronous (SIO) serial data transfer • Full duplex double buffer (Continued) For the information for microcontroller supports, see the following website. http://edevice.fujitsu.com/micom/en-support/ Copyright©2010-2011 FUJITSU SEMICONDUCTOR LIMITED All rights reserved 2011.5 MB95410H/470H Series (Continued) • I2C Built-in wake-up function • External interrupt • Interrupt by edge detection (rising edge, falling edge, and both edges can be selected) • Can be used to wake up the device from different low power consumption (standby) modes • 8/10-bit A/D converter • 8-bit or 10-bit resolution can be selected • LCD controller (LCDC) • On MB95F414H/F414K/F416H/F416K/F418H/F418K, LCD output can be selected from 40 SEG × 4 COM to 36 SEG × 8 COM. • On MB95F474H/F474K/F476H/F476K/F478H/F478K, LCD output can be selected from 32 SEG × 4 COM to 28 SEG × 8 COM. • Internal divider resistor whose resistance value can be selected from 10 kΩ or 100 kΩ through software • Interrupt in sync with the LCD module frame frequency • Blinking function • Inverted display function • Low power consumption (standby) modes • Stop mode • Sleep mode • Watch mode • Time-base timer mode • I/O port • MB95F414H/F416H/F418H (maximum no. of I/O ports: 74) General-purpose I/O ports (N-ch open drain) :3 General-purpose I/O ports (CMOS I/O) : 71 • MB95F414K/F416K/F418K (maximum no. of I/O ports: 75) General-purpose I/O ports (N-ch open drain) :4 General-purpose I/O ports (CMOS I/O) : 71 • MB95F474H/F476H/F478H (maximum no. of I/O ports: 58) General-purpose I/O ports (N-ch open drain) :3 General-purpose I/O ports (CMOS I/O) : 55 • MB95F474K/F476K/F478K (maximum no. of I/O ports: 59) General-purpose I/O ports (N-ch open drain) :4 General-purpose I/O ports (CMOS I/O) : 55 • On-chip debug • 1-wire serial control • Serial writing supported (asynchronous mode) • Hardware/software watchdog timer • Built-in hardware watchdog timer • Built-in software watchdog timer • Low-voltage detection reset circuit Built-in low-voltage detector • Clock supervisor counter Built-in clock supervisor counter function • Programmable port input voltage level CMOS input level / hysteresis input level • Dual operation Flash memory The program/erase operation and the read operation can be executed in different banks (upper bank/lower bank) simultaneously. • Flash memory security function Protects the content of the Flash memory 2 DS702-00004-1v0-E MB95410H/470H Series ■ PRODUCT LINE-UP • MB95410H Series Part number MB95F414H Package MB95F416H MB95F418H MB95F414K MB95F416K MB95F418K Type Flash memory product Clock supervisor It supervises the main clock oscillation. counter Program ROM 20 Kbyte 36 Kbyte 60 Kbyte 20 Kbyte 36 Kbyte 60 Kbyte capacity RAM capacity 496 bytes 1008 bytes 2032 bytes 496 bytes 1008 bytes 2032 bytes Low-voltage No Yes detection reset Reset input Dedicated Selected through software • Number of basic instructions : 136 • Instruction bit length : 8 bits • Instruction length : 1 to 3 bytes CPU functions • Data bit length : 1, 8 and 16 bits • Minimum instruction execution time : 61.5 ns (machine clock frequency = 16.25 MHz) • Interrupt processing time : 0.6 µs (machine clock frequency = 16.25 MHz) • I/O ports (Max) : 75 • I/O ports (Max) : 74 General• CMOS I/O : 71 • CMOS I/O : 71 purpose I/O • N-ch open drain: 4 • N-ch open drain: 3 Time-base timer Interval time: 0.256 ms - 8.3 s (external clock frequency = 4 MHz) • Reset generation cycle Hardware/ software Main oscillation clock at 10 MHz: 105 ms (Min) watchdog timer • The su.


MB95F478H MB95F478K EUP3466


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)