Document
SW75 Series
WASHDOWN
Brick Light
product introduction
The SW75 Series features a stainless steel IP69K rated enclosure with sealed bolts and waterproof connector for applications in wash down and corrosive environments. The SW75 comes equipped with NPN and PNP signal input for strobe and offers a 0-10 VDC analog intensity control as well as a manual intensity control potentiometer. Six high current LED’s are mounted to an aluminum back plate of which is mounted to the stainless steel enclosure for extra heat dissipation ability.
product features
IP69K Standards Stainless Steel 316 Housing Meets FDA Compliancy PNP and NPN Strobe input Continuous operation or Strobe mode Dimmable via built in potentiometer Analog intensity 0-10VDC signal Six, 1mm² Die High Current LEDs
product specifications
Electrical Input Current Wattage Strobe Input PNP Line NPN Line Continuous Mode Potentiometer Analog Intensity Connection Ambient Temp. Lifespan IP Rating Compliances Weight IEC 62471 Rating
24 VDC +/- 5% Max. 400mA Max. 9.6W PNP ► +3VDC or greater to activate. │ NPN ► GND (<1VDC) to activate 30.4mA @ 24 VDC 3.7mA @ 3VDC │6.2mA @ 5VDC │ 12.6mA @ 10VDC │ 22mA @ Common (0VDC) Light will be in continuous mode by leaving signal on strobe input active Intensity control of 10% to 100% Clockwise increases intensity The output is adjustable from 10 -100% of brightness by a 0 -10 VDC signal 5 pin M12 connector -20º - 50º C (-4º - 122º F) 100,000 hrs IP69K CE and RoHS ~710g See page 4
Smart Vision Lights • 2359 Holton Rd. • Muskegon, MI 49445 •Phone 231.722.1199 www.smartvisionlights.com
Free Datasheet http://www.Datasheet4U.com
product number key
SW75 – XXX – X* ─» Part Number Key
Product Family: Brick Light SW75 Color: 470, 505, 530, 625, 850, 940 & WHI (White) Lenses: W-Wide L-Line * Lights come standard with Narrow lenses CE and RoHS Compliant
warnings
!
Attention
Please note that the power requirements are up to 400mA at 24VDC. Failure to supply light with up to 400mA can result in non-repeatable lighting. Contact Smart Vision Lights for more information.
wiring configuration
Standard M12 mating cable color code: 1 – 24V 2 – NPN 3 – GND 4 – PNP 5 – 0-10V BROWN WHITE BLUE BLACK *GRAY (GREEN/YELLOW)
If Analog 0-10 VDC is not used to control light intensity; +VDC (24VDC) must be connected to Analog Input - Jumper pin 5 to pin 1
PIN
1 2 3 4 5
Wire Color
BROWN WHITE BLUE BLACK GREEN
Function
Power NPN Strobe Ground PNP Strobe Analog Intensity Control
Signal
+24 VDC GND for Active ON GND 4VDC to 30VDC for Active ON 0-10 VDC
Smart Vision Lights • 2359 Holton Rd. • Muskegon, MI 49445 •Phone 231.722.1199 www.smartvisionlights.com
Free Datasheet http://www.Datasheet4U.com
optical performance
SW75-XXX
Working Distance mm (inches) .5m (19.7") 1m (39.4") 1.5m (59") Typical output performance Distance = .5 meter Pattern (80%-100% measured intensity) mm (Inches) 100mm (~4”) D 200mm(~8”) D 300mm(~12”) D Illumination (Lux) 9600
Illumination me.