Preliminary
SF1183B
• • • • RF Filter for Mobile Communication Applications Low Insertion Loss 3.0 x 3.0 x 1.3 mm Surface-Mount Case No Matching Circuit Required
881.5 MHz SAW Filter
Value +10 -5 to +5 -40 to +100 265°C for 10 s Units dBm VDC °C
Absolute Maximum Ratings
Rating Maximum Incident Power in Passband Max. DC voltage between any 2 terminals Storage Temperature Range Max Soldering Profile
SM3030-6
Electrical Characteristics
Characteristic Nominal Operating Frequency Passband Insertion Loss across 869-894 Amplitude Ripple p-p across 869-894 Attenuation 10 -849 MHz 914 -939 MHz 939 -1049 MHz 1049 -2000 MHz VSWR across 869-894 Source impedance Load impedance Operating Temperature Single Ended Input / Output, Impedance match Case Style Lid Symbolization (Y=year, WW=week, S=shift) Sym fC IL Notes 1 Min Typ 881.5 2.0 1.0 23.0 30.0 25.0 24.5 1.7 50 50 Max 3.0 2.0 Units MHz dB
1, 2, 3
20 20 23.0 20
dB
2.5 Ω Ω °C
ZS ZL TA
www.DataSheet.net/
1
-30
+85
No matching network required for operation at 50 ohms SM3030-6 3 x 3 mm Nominal Footprint 449 YWWS
Electrical Connections
Connection Input Output Ground Terminals 2 5 All others
50 pin 2 pin 5
SAW Filter
TOP VIEW 50
All Others
Notes: 1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. 2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. 4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5.
The design, manufacturing process, and specifications of this filter are subject to change. 6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. 7. US and international patents may apply. 8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. 9. ©Copyright 1999, RF Monolithics Inc. 10. Electrostatic Sensitive Device. Observe precautions for handling.
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail:
[email protected] http://www.rfm.com SF1183B-081902 532-1183-001
Page 1 of 5
Datasheet pdf - http://www.DataSheet4U.co.kr/
881.5 MHz
Frequency Characteristics wideband response:
SAW Filter
www.DataSheet.net/
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail:
[email protected] http://www.rfm.com SF1183B-081902 532-1183-001
Page 2 of 5
Datasheet pdf - http://www.DataSheet4U.co.kr/
881.5 MHz
SAW Filter
Reflections Functions: S11 VSWR
S22 VSWR
www.DataSheet.net/
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail:
[email protected] http://www.rfm.com SF1183B-081902 532-1183-001
Page 3 of 5
Datasheet pdf - http://www.DataSheet4U.co.kr/
881.5 MHz
Tape and Reel Specifications
SAW Filter
“B “ Nominal Size Inches
100 REF. "B" REF.
Quantity Per Reel 500 2000
millimeters 178 330
7 13
See Detail "A" 12.0
0 13.
20 .2
www.DataSheet.net/
2.0
COMPONENT ORIENTATION
0.3 2.0 4.0 1.5 A
RO.3 (MAX.)
5.5
3.35 B B 8.0 A R0.5 (TYP.)
1.75 12.0
Page 4 of 5
PIN #1
1.4
3.35
1.5 SECTION A-A SECTION B-B
USER DIRECTION OF FEED
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail:
[email protected] http://www.rfm.com SF1183B-081902 532-1183-001
Datasheet pdf - http://www.DataSheet4U.co.kr/
881.5 MHz
SAW Filter
SM3030-6 Case
6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint
Case Dimensions
Dimension A B C D E F G H I J Min mm Nom 3.0 3.0 1.3 0.9 2.54 1.6 0.85 1.5 0.6 1.3 Max Min Inches Nom 0.118 0.118 0.051 0.035 0.100 0.063 0.033 0.059 0.024 0.051 Max
Electrical Connections
Connection Port 1
www.DataSheet.net/
Terminals 2 5 All others
Single Ended Input Single Ended Output Ground
Port 2
Single Ended Operation Only Dot indicates Pin 1
TOP VIEW
B 1 6 C 6
BOTTOM VIEW
G H 1
A 2
5
E
F
5
2
I
3
4 D
4 J.