DatasheetsPDF.com

IPS7081PBF Dataheets PDF



Part Number IPS7081PBF
Manufacturers International Rectifier
Logo International Rectifier
Description INTELLIGENT POWER HIGH SIDE SWITCH
Datasheet IPS7081PBF DatasheetIPS7081PBF Datasheet (PDF)

Data sheet N° PD60308 IPS7081(R)(S)PbF INTELLIGENT POWER HIGH SIDE SWITCH Features • • • • • • • • Over temperature shutdown (with auto-restart) Short circuit protection (current limit) Active clamp Open load detection Logic ground isolated from power ground ESD protection Ground loss protection Status feedback Product Summary Rds(on) Vclamp I Limit Open load Package 70mΩ max. 70V 5A (typ.) 3V Description The IPS7081(R)(S)PbF is a five terminal Intelligent Power Switch (IPS) with built in sho.

  IPS7081PBF   IPS7081PBF



Document
Data sheet N° PD60308 IPS7081(R)(S)PbF INTELLIGENT POWER HIGH SIDE SWITCH Features • • • • • • • • Over temperature shutdown (with auto-restart) Short circuit protection (current limit) Active clamp Open load detection Logic ground isolated from power ground ESD protection Ground loss protection Status feedback Product Summary Rds(on) Vclamp I Limit Open load Package 70mΩ max. 70V 5A (typ.) 3V Description The IPS7081(R)(S)PbF is a five terminal Intelligent Power Switch (IPS) with built in short circuit, over-temperature, ESD protection, inductive load capability and diagnostic feedback. The output current is limited at Ilim value. Current limitation is activated until the thermal protection acts. The over-temperature protection turns off the device if the junction temperature exceeds Tshutdown. It will automatically restart after the junction has cooled 7°C below Tshutdown. A diagnostic pin is provided for status feedback of short circuit, over-temperature and open load detection. The double level shifter circuitry allows large offsets between the logic ground and the load. TO220 D²Pak IPS7081PbF IPS7081SPbF D-Pak IPS7081RPbF Typical Connection +5V +Bat Vcc(3) Dg(4) Control Rdg In(2) V Diag Rin Input Signal Load Gnd(1) Out(5) Pull-up resistor for Open Load Off detection 15K www.irf.com www.DataSheet.in 1 IPS7081(R)(S) Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are referenced to Ground lead. (Tambient=25°C unless otherwise specified). Symbol Vout Voffset Vin Vcc max. Vcc cont. Iin max. Idg max. Vdg Pd Isd cont. ESD1 ESD2 Tj max. Parameter Maximum output voltage Maximum logic ground to load ground offset Maximum input voltage Maximum Vcc voltage Maximum continuous Vcc voltage Maximum IN current Maximum diagnostic output current Maximum diagnostic output voltage Maximum power dissipation (internally limited by thermal protection) Rth=50°C/W Maximum continuous diode current (Rth=50°C/W) Electrostatic discharge voltage (Human body) 100pF, 1500Ω Electrostatic discharge voltage (Machine Model) C=200pF,R=0Ω,L=10µH Max. storage & operating temperature junction temperature Min. Max. Units V Vcc-65 Vcc+0.3 Vcc-65 Vcc+0.3 -0.3 5.5 ⎯ 65 ⎯ 35 -1 10 -1 10 -0.3 5.5 ⎯ ⎯ ⎯ ⎯ mA V W A kV °C 2.5 2.2 4 0.5 +150 -40 Thermal Characteristics Symbol Rth1 Rth2 Rth3 Rth1 Parameter Thermal resistance junction to ambient D-Pak std. footprint Thermal resistance junction to ambient D-Pak 1” sqrt. footprint Thermal resistance junction to case D-Pak / TO220 / D²Pak Thermal resistance junction to ambient TO220 free air Typ. 70 50 3 60 Max. ⎯ ⎯ ⎯ ⎯ Units °C/W Recommended Operating Conditions These values are given for a quick design. For operation outside these conditions, please consult the application notes. Symbol VIH VIL Iout Rin Rdgs Rol Parameter High level input voltage Low level input voltage Continuous drain current, Tamb=85°C, Tj=125°C, Vin=5V, Rth=50°C/W Recommended resistor in series with IN pin Recommended resistor in series with DG pin Recommended pull-up resistor for open load detection Min. 4 -0.3 ⎯ Max. 5.5 0.9 2.3 10 20 100 Units A kΩ 4 10 5 www.irf.com www.DataSheet.in 2 IPS7081(R)(S) Static Electrical Characteristics Tj=25°C, Vcc=14V (unless otherwise specified) Symbol Rds(on) Vcc op. V clamp 1 V clamp 2 Vf Icc Off Icc On Iout@0V Iout@6V Idg leakage Vdgl Vih Vil In hys UV high UV low UV hys Iin On Parameter ON state resistance Tj=25°C ON state resistance Tj=150°C ON state resistance Tj=25°C, Vcc=6.5V Operating voltage range Vcc to Out clamp voltage 1 Vcc to Out clamp voltage 2 Body diode forward voltage Supply current when Off Supply current when On Output leakage current Output leakage current Diagnostic output leakage current Low level diagnostic output voltage Input high threshold voltage Input low threshold voltage Input hysteresis Under voltage high threshold voltage Under voltage low threshold voltage Undervoltage hysteresis Input current when device is On Min. ⎯ ⎯ ⎯ Typ. 55 100 60 ⎯ Max. 70 130 80 35 ⎯ Units mΩ Test Conditions Vin=5V, Iout=2A Vin=5V, Iout=2A Vin=5V, Iout=2A Iout=30mA (see Fig. 1) Iout=2A (see Fig. 1) Iout= 2.5A Vin=0V, Vout=0V Vin=5V Vout=0V Vout=6V Vdg=5.5V Idg=1.6mA 6 65 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 1 70 70 1 2.5 2.5 2.5 20 ⎯ 75 1.35 10 3.5 10 ⎯ V µA mA µA 0.15 ⎯ 3.4 0.1 ⎯ 0.2 2.5 2 0.5 5 4.5 0.5 40 10 0.3 3.5 ⎯ 1 5.9 ⎯ V 1.5 80 µA Vin=5V Switching Electrical Characteristics Vcc=14V, Resistive load=6Ω, Vin=5V, Tj=25°C Symbol Tdon Tr1 Tr2 dV/dt (On) EOn Tdoff Tf dV/dt (Off) EOff Tdiag Parameter Turn-on delay time Rise time to Vout=Vcc-5V Rise time to Vout=0.9 x Vcc Turn On dV/dt Turn On energy Turn-off delay time Fall time to Vout=0.1 x Vcc Turn Off dV/dt Turn Off energy Vout to Vdiag propagation delay Min. ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Typ. 16 10 20 0.8 100 25 7.5 1.6 25 15 Max. 45 40 100 3 ⎯ Units µs V/µs µJ µs V/µs µJ µs Test Conditions See Fig. 3 50 2.


IPS7071GPBF IPS7081PBF IPS7081RPBF


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)