DatasheetsPDF.com

IPS7071GPBF Dataheets PDF



Part Number IPS7071GPBF
Manufacturers International Rectifier
Logo International Rectifier
Description PROTECTED HIGH SIDE SWITCH
Datasheet IPS7071GPBF DatasheetIPS7071GPBF Datasheet (PDF)

Data sheet No. PD60309 IPS7071GPbF PROTECTED HIGH SIDE SWITCH Features • • • • • • • • Over temperature shutdown (with auto-restart) Short circuit protection (current limit) Active clamp Open load detection Logic ground isolated from power ground ESD protection Ground loss protection Status feedback Product Summary Rds(on) Vclamp I Limit Open load Package 110mΩ max. 70V 5A 3V Description The IPS7071GPbF is a fully protected five terminal high side switch with built in short circuit, over-temp.

  IPS7071GPBF   IPS7071GPBF


Document
Data sheet No. PD60309 IPS7071GPbF PROTECTED HIGH SIDE SWITCH Features • • • • • • • • Over temperature shutdown (with auto-restart) Short circuit protection (current limit) Active clamp Open load detection Logic ground isolated from power ground ESD protection Ground loss protection Status feedback Product Summary Rds(on) Vclamp I Limit Open load Package 110mΩ max. 70V 5A 3V Description The IPS7071GPbF is a fully protected five terminal high side switch with built in short circuit, over-temperature, ESD protection, inductive load capability and diagnostic feedback. The output current is limited at Ilim value. Current limitation is activated until the thermal protection acts. The over-temperature protection turns off the device if the junction temperature exceeds Tshutdown. It will automatically restart after the junction has cooled 7°C below Tshutdown. A diagnostic pin is provided for status feedback of short circuit, over-temperature and open load detection. The double level shifter circuitry allows large offsets between the logic ground and the load. SO8 IPS7071GPbF Typical Connection +5V +Bat Vcc Dg Control Rdg In V Diag Rin Input Signal Load Gnd Out Pull-up resistor for Open Load Off detection 15K www.irf.com www.DataSheet.in 1 IPS7071GPbF Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are referenced to Ground lead. (Tambient=25°C unless otherwise specified). Symbol Vout Voffset Vin Vcc max. Vcc cont. Iin max. Idg max. Vdg Pd Isd cont. ESD1 ESD2 Tj max. Parameter Maximum output voltage Maximum logic ground to load ground offset Maximum input voltage Maximum Vcc voltage Maximum continuous Vcc voltage Maximum IN current Maximum diagnostic output current Maximum diagnostic output voltage Maximum power dissipation (internally limited by thermal protection) Rth=100°C/W Maximum continuous diode current (Rth=100°C/W) Electrostatic discharge voltage (Human body) 100pF, 1500Ω Electrostatic discharge voltage (Machine Model) C=200pF,R=0Ω,L=10µH Max. storage & operating temperature junction temperature Min. Max. Units V Vcc-65 Vcc+0.3 Vcc-65 Vcc+0.3 -0.3 5.5 ⎯ 65 ⎯ 35 -1 10 -1 10 -0.3 5.5 ⎯ ⎯ ⎯ ⎯ mA V W A kV °C 1.25 1.8 4 0.5 +150 -40 Thermal Characteristics Symbol Rth1 Parameter Thermal resistance junction to ambient IPS7071G Typ. 100 Max. ⎯ Units °C/W Recommended Operating Conditions These values are given for a quick design. For operation outside these conditions, please consult the application notes. Symbol VIH VIL Iout Rin Rdgs Rol Parameter High level input voltage Low level input voltage Continuous drain current, Tamb=85°C, Tj=125°C, Vin=5V, Rth=100°C/W Recommended resistor in series with IN pin Recommended resistor in series with DG pin Recommended pull-up resistor for open load detection Min. 4 -0.3 ⎯ Max. 5.5 0.9 1.5 10 20 100 Units A kΩ 4 10 5 www.irf.com www.DataSheet.in 2 IPS7071GPbF Static Electrical Characteristics Tj=25°C, Vcc=14V (unless otherwise specified) Symbol Parameter Min. ⎯ ⎯ ⎯ Typ. 80 130 90 ⎯ Max. 110 175 120 35 ⎯ Units mΩ Test Conditions Vin=5V, Iout=2.5A Vin=5V, Iout=2.5A Vin=5V, Iout=2.5A Iout=10mA (see Fig. 1) Iout=1A (see Fig. 1) Iout= 2.5A Vin=0V, Vout=0V Vin=5V Vout=0V Vout=6V Vdg=5.5V Idg=1.6mA ON state resistance Tj=25°C Rds(on) ON state resistance Tj=150°C (1) ON state resistance Tj=25°C, Vcc=6.5V Vcc op. Operating voltage range V clamp 1 Vcc to Out clamp voltage 1 V clamp 2 Vcc to Out clamp voltage 2 (1) Vf Body diode forward voltage Icc Off Supply current when Off Icc On Supply current when On Iout@0V Output leakage current Iout@6V Output leakage current Idg leakage Diagnostic output leakage current Vdgl Low level diagnostic output voltage Vih Input high threshold voltage Vil Input low threshold voltage In hys Input hysteresis UV high Under voltage high threshold voltage UV low Under voltage low threshold voltage UV hys Undervoltage hysteresis Iin On Input current when device is On (1) Guaranteed by design 6 65 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 1 70 70 1 2.5 2.5 1.1 75 1.35 10 3.5 10 ⎯ V µA mA µA 20 ⎯ 0.15 ⎯ 3.4 0.1 ⎯ 0.2 2.5 2 0.4 5 4.5 0.8 40 10 0.3 3.5 ⎯ 1 5.9 ⎯ V 1.5 80 µA Vin=5V Switching Electrical Characteristics Vcc=14V, Resistive load=14Ω, Vin=5V, Tj=25°C Symbol Tdon Tr1 Tr2 dV/dt (On) EOn Tdoff Tf dV/dt (Off) EOff Tdiag Parameter Turn-on delay time Rise time to Vout=Vcc-5V Rise time to Vout=0.9 x Vcc Turn On dV/dt Turn On energy Turn-off delay time Fall time to Vout=0.1 x Vcc Turn Off dV/dt Turn Off energy Vout to Vdiag propagation delay Min. ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Typ. 11 7 15 1.3 75 23 6 2 25 15 Max. 35 40 50 4 ⎯ Units µs V/µs µJ µs V/µs µJ µs Test Conditions See Fig. 3 45 25 6 ⎯ ⎯ See Fig. 4 and Fig. 12 www.irf.com www.DataSheet.in 3 IPS7071GPbF Protection Characteristics Symbol Parameter Min. 2 150(2) ⎯ 2 2 Typ. 5 165 158 3 3 Max. 9 ⎯ ⎯ Units A °C V Test Conditions Vout=0V See Fig. 2 Ilim Internal current limit.


HTA20015D IPS7071GPBF IPS7081PBF


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)