DatasheetsPDF.com

W583S30 Dataheets PDF



Part Number W583S30
Manufacturers Winbond
Logo Winbond
Description HIGH FIDELITY Power Speech
Datasheet W583S30 DatasheetW583S30 Datasheet (PDF)

www.DataSheet4U.com Preliminary W583XXX HIGH FIDELITY Power Speech TM GENERAL DESCRIPTION W583xxx are fabricated using the Winbond CMOS process. The W583xxx family is a new member of the PowerSpeech synthesizer series, with voice quality which is even better than before. The W583xxx family has adopted the same architecture as the PowerSpeech synthesizers while replacing the 4-bit ADPCM algorithm with Winbond′s new high fidelity voice synthesis algorithm to produce better quality voice. W583xx.

  W583S30   W583S30



Document
www.DataSheet4U.com Preliminary W583XXX HIGH FIDELITY Power Speech TM GENERAL DESCRIPTION W583xxx are fabricated using the Winbond CMOS process. The W583xxx family is a new member of the PowerSpeech synthesizer series, with voice quality which is even better than before. The W583xxx family has adopted the same architecture as the PowerSpeech synthesizers while replacing the 4-bit ADPCM algorithm with Winbond′s new high fidelity voice synthesis algorithm to produce better quality voice. W583xxx provides IR function, CPU interface, pad option for Ring or Crystal oscillator and voice output in DAC current or PWM type. According different voice duration, there are 11 bodies in W583xxx family, list them below. PART NO. Duration PART NO. Duration W583S10 10 sec W583S50 50 sec W583S15 15 sec W583S60 60 sec W583S20 20 sec W583S80 80 sec W583S25 25 sec W583S99 99 sec W583S30 30 sec W583M02 120 sec W583S40 40 sec Notes: 1. The voice duration is estimated by 6.4 KHz sampling rate. 2. W583S10 provides less I/O pins, and do not provide crystal oscillator. FEATURES • Programmable speech synthesizer • New high fidelity synthesis algorithm • Wide operating voltage range: 2.4 - 5.5 Volts • Direct drive speaker by PWM output or Built-in 8-bit D/A converter • Supports CPU interface operation • IR interface for command Transmission and Receiving • Symbolic compiler supported • Instruction cycle ≤ 400 µS typically • Section control − Variable frequency: 4.8/6/8/12 KHz − LED: ON/OFF • Eight general-purpose registers R0-R7 • Pad option for Ring or Crystal oscillator • 8 STOP outputs 3 1 2 • 8 trigger inputs - with separate control of falling/rising edge trigger • Number of interrupt vector / label up to 2,048 Notes: 1. W583S10 provide ring oscillator only. 2. Only 4 trigger pins in W583S10. 3. Only 5 STOP outputs in W583S10. -1- Publication Release Date: March 1999 Revision A1 www.DataSheet4U.com Preliminary W583XXX BLOCK DIAGRAM W583S15 to W583M02 RESET OSC/XIN XOUT SEL TG1 : TG3/IRIN : TG8 STPA/BUSY STPB LED2/STPC : STPH LED1 TIMING GENERATOR ROM CONTROLLER SPEECH SYNTHESIZER D/A CONVERTER PWM DRIVER VDD1 VSS1 IROUT VDD VSS TEST AUD/SPK+ SPK- W583S10 RESET OSC OSCO TG1 TG2 TG3/IRIN TG4 STPA/BUSY STPB LED2/STPC STPD STPE LED1 IROUT VDD VSS TEST AUD/SPK+ SPKD/A CONVERTER PWM DRIVER VDD1 VSS1 TIMING GENERATOR ROM CONTROLLER SPEECH SYNTHESIZER -2- www.DataSheet4U.com Preliminary W583XXX PIN DESCRIPTION NAME VDD TEST RESET I/O I I I I I Positive power supply DESCRIPTION Test pin, internally pulled low Reset all, functions as POR, internally pulled high Direct trigger input 1, internally pulled high Direct trigger input 2, internally pulled high Direct trigger input 3 or IR input, internally pulled high. Once this pin is pulled low, the oscillation circuit is active even the chip enters standby mode. Direct trigger input 4, internally pulled high Negative power supply LED1 output IR signal output pin, active low Stop signal A or Busy signal Stop signal B LED2 output or Stop signal C Stop signal D Stop signal E Current type output or PWM output for speaker PWM output Negative power supply Positive power supply TG1 TG2 TG3/IRIN TG4 VSS LED1 IROUT STPA/BUSY STPB LED2/STPC STPD STPE AUD/SPK+ SPKVSS1 VDD1 I O O O O O O O O O - Pin Description only for W583S15 to W583M02 NAME OSC/XIN XOUT SEL TG5 TG6 TG7 I/O I I/O I I I I DESCRIPTION Ring oscillator input or crystal input Crystal input or oscillator clock output Ring/Crystal oscillator select, internally pulled high. Floating for Ring and grounded for crystal. Direct trigger input 5, internally pulled high Direct trigger input 6, internally pulled high Direct trigger input 7, internally pulled high -3- Publication Release Date: March 1999 Revision A1 www.DataSheet4U.com Preliminary W583XXX Pin Description only for W583S15 to W583M02, continued NAME TG8 STPF STPG STPH I/O I O O O Stop signal F Stop signal G Stop signal H DESCRIPTION Direct trigger input 8, internally pulled high Pin Description only for W583S10 NAME OSC OSCO I/O I O Ring oscillator input Oscillator clock output DESCRIPTION FUNCTIONAL DESCRIPTION The W583xxx is a derivative of Winbond's PowerSpeech synthesizers, which are becoming dominant in the consumer market, especially for toy applications. There are up to 8 trigger inputs and 8 STOP outputs in W583xxx. The maximal number of software key pad by scanning matrix is up to 8 × 9 = 72 keys. There are 8 general purpose registers, R0-R7. R0-R7 can apply not only for "LD" and "JP" instructions but also for "MV" instruction. Only R0 can apply for "INC" instruction. CPU interface is the same as the W581xx series. IR interface is a new feature of PowerSpeech. User can use IR interface to transmit and receive a command. For example, when X chip executes the "TX R1" instruction, the Pulse Position Modulation waveform (with 38 KHz carrier) outputs from IROUT pin to drive a photo diode. Y chips within a certain distance will receive the IR s.


W583S25 W583S30 W583S40


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)