DatasheetsPDF.com

ICS524 Dataheets PDF



Part Number ICS524
Manufacturers Integrated Device Technology
Logo Integrated Device Technology
Description LOW SKEW 1 TO 4 CLOCK BUFFER
Datasheet ICS524 DatasheetICS524 Datasheet (PDF)

www.DataSheet4U.com DATASHEET LOW SKEW 1 TO 4 CLOCK BUFFER Description The ICS524 is a low skew, single input to four output, clock buffer. Part of ICS’ ClockBlocksTM family, this is our lowest skew, small clock buffer. See the ICS552-02 for a 1 to 8 low skew buffer. For more than eight outputs, see the MK74CBxxx BuffaloTM series of clock drivers. ICS makes many non-PLL and PLL based low skew output devices as well as Zero Delay Buffers to synchronize clocks. Contact us for all of your clockin.

  ICS524   ICS524



Document
www.DataSheet4U.com DATASHEET LOW SKEW 1 TO 4 CLOCK BUFFER Description The ICS524 is a low skew, single input to four output, clock buffer. Part of ICS’ ClockBlocksTM family, this is our lowest skew, small clock buffer. See the ICS552-02 for a 1 to 8 low skew buffer. For more than eight outputs, see the MK74CBxxx BuffaloTM series of clock drivers. ICS makes many non-PLL and PLL based low skew output devices as well as Zero Delay Buffers to synchronize clocks. Contact us for all of your clocking needs. ICS524 Features • • • • • • • • Extremely low skew outputs (50 ps maximum) Packaged in 8-pin SOIC Available in Pb (lead) free package Low power CMOS technology Operating voltages of 2.5 V to 5 V Output Enable pin tri-states outputs 5 V tolerant input clock Industrial temperature range Block Diagram Q0 Q1 ICLK Q2 Q3 IDT™ / ICS™ LOW SKEW 1 TO 4 CLOCK BUFFER 1 ICS524 REV A 101705 ICS524 LOW SKEW 1 TO 4 CLOCK BUFFER www.DataSheet4U.com FAN OUT BUFFER Pin Assignment ICLK Q0 Q1 NC 1 2 3 4 8 7 6 5 8-pin SOIC GND Q3 Q2 VDD Pin Descriptions Pin Pin Number Name 1 2 3 4 5 6 7 8 ICLK Q0 Q1 NC VDD Q2 Q3 GND Pin Type Input Output Output Power Output Output Power Clock input, 5V tolerant input. Clock output 0. Clock output 1. Pin Description Do not connect this pin to anything. Connect to +2.5 V, +3.3 V or +5.0 V. Clock Output 2. Clock Output 3. Connect to ground. External Components A minimum number of external components are required for proper operation. A decoupling capacitor of 0.01 µF should be connected between VDD on pin 5 and GND on pin 8, as close to the device as possible. A 33 Ω series terminating resistor may be used on each clock output if the trace is longer than 1 inch. To achieve the low output skew that the ICS524 is capable of, careful attention must be paid to board layout. Essentially, all four outputs must have identical terminations, identical loads and identical trace geometries. If they do not, the output skew will be degraded. For example, using a 30Ω series termination on one output (with 33Ω on the others) will cause at least 15 ps of skew. IDT™ / ICS™ LOW SKEW 1 TO 4 CLOCK BUFFER 2 ICS524 REV A 101705 ICS524 LOW SKEW 1 TO 4 CLOCK BUFFER www.DataSheet4U.com FAN OUT BUFFER Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS524. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Supply Voltage, VDD Output Enable and All Outputs ICLK Ambient Operating Temperature Storage Temperature Junction Temperature Soldering Temperature 7V Rating -0.5 V to VDD+0.5 V -0.5 V to 5.5 V -40 to +85°C -65 to +150°C 125°C 260°C Recommended Operation Conditions Parameter Ambient Operating Temperature Power Supply Voltage (measured in respect to GND) Min. -40 +2.375 Typ. Max. +85 +5.25 Units °C V DC Electrical Characteristics VDD=2.5 V ±5%, Ambient temperature -40 to +85°C, unless stated otherwise Parameter Operating Voltage Input High Voltage, ICLK Input Low Voltage, ICLK Output High Voltage Output Low Voltage Operating Supply Current Nominal Output Impedance Input Capacitance Short Circuit Current Symbol VDD VIH VIL VOH VOL IDD ZO CIN IOS Conditions Note 1 Note 1 IOH = -16 mA IOL = 16 mA No load, 135 MHz ICLK Min. 2.375 VDD/2+0.5 2 Typ. Max. 2.625 5.5 VDD/2-0.5 0.4 Units V V V V V mA Ω pF mA 25 20 5 ±28 IDT™ / ICS™ LOW SKEW 1 TO 4 CLOCK BUFFER 3 ICS524 REV A 101705 ICS524 LOW SKEW 1 TO 4 CLOCK BUFFER www.DataSheet4U.com FAN OUT BUFFER DC Electrical Characteristics (continued) VDD=3.3 V ±5% , Ambient temperature -40 to +85°C, unless stated otherwise Parameter Operating Voltage Input High Voltage, ICLK Input Low Voltage, ICLK Output High Voltage Output Low Voltage Output High Voltage (CMOS Level) Operating Supply Current Nominal Output Impedance Input Capacitance Short Circuit Current Symbol VDD VIH VIL VOH VOL VOH IDD ZO CIN IOS Conditions Note 1 Note 1 IOH = -25 mA IOL = 25 mA IOH = -12 mA No load, 135 MHz ICLK Min. 3.15 VDD/2+0.7 2.4 Typ. Max. 3.45 5.5 VDD/2-0.7 0.4 Units V V V V V V VDD-0.4 35 20 5 ±50 mA Ω pF mA VDD=5 V ±5% , Ambient temperature -40 to +85°C, unless stated otherwise Parameter Operating Voltage Input High Voltage, ICLK Input Low Voltage, ICLK Output High Voltage Output Low Voltage Output High Voltage (CMOS Level) Operating Supply Current Nominal Output Impedance Input Capacitance Short Circuit Current Symbol VDD VIH VIL VOH VOL VOH IDD ZO CIN IOS Conditions Note 1 Note 1 IOH = -35 mA IOL = 35 mA IOH = -12 mA No load, 135 MHz ICLK Min. 4.75 VDD/2+1 2.4 Typ. Max. 5.25 5.5 VDD/2-1 0.4 Units V V V V V.


ICS514 ICS524 ICS525-11


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)