DatasheetsPDF.com

ALN1811 Dataheets PDF



Part Number ALN1811
Manufacturers Advanced Semiconductor
Logo Advanced Semiconductor
Description Internally Matched LNA Module
Datasheet ALN1811 DatasheetALN1811 Datasheet (PDF)

plerowTM ALN1811 www.DataSheet4U.com Internally Matched LNA Module Description The plerowTM ALN-series is the compactly designed surface-mount module for the use of the LNA with or without the following gain blocks in the infrastructure equipment of the mobile wireless (CDMA, GSM, PCS, PHS, WCDMA, DMB, WLAN, WiBro, WiMAX), GPS, satellite communication terminals, CATV and so on. It has an exceptional performance of low noise figure, high gain, high OIP3, and low bias current. The stability facto.

  ALN1811   ALN1811


Document
plerowTM ALN1811 www.DataSheet4U.com Internally Matched LNA Module Description The plerowTM ALN-series is the compactly designed surface-mount module for the use of the LNA with or without the following gain blocks in the infrastructure equipment of the mobile wireless (CDMA, GSM, PCS, PHS, WCDMA, DMB, WLAN, WiBro, WiMAX), GPS, satellite communication terminals, CATV and so on. It has an exceptional performance of low noise figure, high gain, high OIP3, and low bias current. The stability factor is always kept more than unity over the application band in order to ensure its unconditionally stable implementation to the application system environment. The surface-mount module package including the completed matching circuit and other components necessary just in case allows very simple and convenient implementation onto the system board in mass production level. Features · 27 dB Gain at 1810 MHz · 18 dBm P1dB · 33 dBm Output IP3 · 0.95 dB Noise Figure · Operating at Single 5 V Supply · 80 mA Current Consumption Specifications (in Production) Typ. @ T = 25°C, Vs = 5 V, Freq. = 1810 MHz, Zo.sys = 50 ohm Parameter Frequency Range Gain Gain Flatness Noise Figure Output IP3 S11 / S22 (1) (2) Unit MHz dB dB dB dBm dB dBm Specifications Min 1750 26 27 ± 0.5 0.95 32 17 33 -18 / -10 18 80 5 50 C.W 29 ~ 31 (before fail) Surface Mount Type, 13Wx13Lx3.8H 100 ± 0.7 1.0 Typ Max 1870 2-stage Single Type More Information Website: www.asb.co.kr E-mail: [email protected] Tel: (82) 42-528-7223 Fax: (82) 42-528-7222 ASB Inc., 4th Fl. Venture Town Bldg., 367-17 Goijeong-Dong, Seo-Gu, Daejon 302-716, Korea Output P1dB Switching Time Supply Current Supply Voltage Impedance Max. RF Input Power Package Type & Size (3) µsec mA V Ω dBm mm Operating temperature is -40°C to +85°C. 1) OIP3 is measured with two tones at an output power of 10 dBm / tone separated by 1 MHz. 2) S11/S22 (max) is the worst value within the frequency band. 3) Switching time means the time that takes for output power to get stabilized to its final level after switching DC voltage from 0 V to VS. Outline Drawing (Unit: mm) Pin Number Function RF In RF Out +Vcc Ground plerow ALN1811 ASB Inc. (Top View) Solder Stencil Area (Bottom View) 3 8 10 Others Note: 1. The number and size of ground via holes in a circuit board is critical for thermal RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of all ground pins for better RF and thermal performance, as shown in the drawing at the left side. (Side View) Ø0.4 plated thru holes to ground plane (Recommended Footprint) 1/3 www.asb.co.kr September 2007 plerowTM ALN1811 www.DataSheet4U.com Internally Matched LNA Module S-parameters Typical Performance (Measured) 1750~1870 +5 V Stability Factor (K) Noise Figure OIP3 P1dB 2/3 www.asb.co.kr September 2007 plerowTM ALN1811 www.DataSheet4U.com Internally Matched LNA Module Application Circuit V DC + - Tantal Capacitor IN C1 ALN C2 OUT 1) The tantal capacitor is optional and for bypassing the AC noise introduced from the DC supply. The capacitance value may be determined by customer’s DC supply status. 2) So-called DC blocking capacitors are always necessarily placed at the input and output port for allowing only the RF signal to pass and blocking the DC component in the signal. The DC blocking capacitors are included inside the LNA module. Therefore, C1 & C2 capacitors may not be necessary, but can be added just in case that the customer wants. The value of C1 & C2 is determined by considering the application frequency. Recommended Soldering Reflow Process 260°C 20~40 sec Evaluation Board Layout +Vcc Ramp-up (3˚C/sec) 200°C Ramp-down (6°C/sec) IN OUT 150°C 60~180 sec Size 25 x 25mm (for ALN Series – 13x13mm) 3/3 www.asb.co.kr September 2007 .


ALN1810M3 ALN1811 ALN1811BT


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)