Document
www.DataSheet4U.com
TA8210AHQ/ALQ
TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic
TA8210AHQ,TA8210ALQ
20W BTL × 2ch Audio Power Amplifier
TA8210AHQ
The thermal resistance θj−T of TA8210AHQ, TA8210ALQ package designed for low thermal resistance, has a high efficiency of heat radiation. The temperature rise of chip can be reduced, and the influence from the degradation of the features due to the temperature rise at the high output can also be reduced. This stereo audio power IC, designed for car audio use, has two built−in channels to reduce the characteristic difference between L and R channels. In addition, the functions of stand−by and muting, and a variety of protection circuits are involved.
TA8210ALQ
Features
• • Low thermal resistance : θj−T = 1.5°C / W (infinite heat sink) High power : POUT (1) = 22W (typ.) / channel (VCC = 14.4V, f = 1kHz, THD = 10%, RL = 4Ω) POUT (2) = 19W (typ.) / channel (VCC = 13.2V, f = 1kHz, THD = 10%, RL = 4Ω) • • • • • • Low distortion ratio: THD = 0.04% (typ.) (VCC = 13.2V, f = 1kHz, POUT = 1W, RL = 4Ω, GV = 50dB) Low noise: VNO = 0.30mVrms (typ.) (VCC = 13.2V, RL = 4Ω, GV 50dB, Rg = 0Ω, BW = 20Hz~20kHz) Built−in stand−by function (with pin(4) set at low, power is turned off.): ISB = 1µA (typ.) Built−in muting function (with pin(1) set at low, power is turned off.): V (mute) = 1V (typ.) Built−in various protection circuits Protection circuits: Thermal shut down, Over voltage, Out→VCC short, Out→GND short and Out−Out short. Operating supply voltage: VCC = 9~18V Weight HZIP17-P-2.00: 9.8g (typ.) HSIP17-P-2.00: 9.8g (typ.)
1
2006-04-28
www.DataSheet4U.com
TA8210AHQ/ALQ
Block Diagram
TA8210AHQ, TA8210ALQ (GV = 50dB)
Cautions And Application Method
1. Voltage gain adjustment
(description is made only on the single channel.)
This IC has the amplifier construction as shown in Fig.1. The pre−amp (amp 1) is provided to the primary stage, and the input voltage is amplified by the flat amps, amp 3 and amp 4 of each channel through the phase amp. (Amp 2). Since the input offset is prevented by pre−amp when VCC is set to on, this circuit can remarkably reduce the pop noise.
2
2006-04-28
www.DataSheet4U.com
TA8210AHQ/ALQ
The total closed loop gain GV of this IC can be obtained by expression below when the closed loop voltage gain of amp 1 is GV1.
G V1 = 20log R1 + (Rf + R2) (dB) R f + R2
..... (1)
The closed loop voltage gain of power amp, amp 3 and amp 4 is fixed at GV3≒GV4 = 20dB. Therefore, the total closed circuit voltage gain GV is obtained through BTL connection by the expression below. GV = GV1 + GV3 + 6 (dB) ............... (2) For example, when Rf = 0Ω, GV is obtained by the expressions (1) and (2) as shown below. GV≒24 + 20 + 6 = 50dB The voltage gain is reduced when Rf is increased. (Fig.2) With the voltage gain reduced, since (1) the oscillation stability is reduced, and (2) the pop noise changes when VCC is set to on, refer to the items 3 and 4.
Fig.2
2. Stand−by SW function By mea.