DatasheetsPDF.com

ADATE206 Dataheets PDF



Part Number ADATE206
Manufacturers Analog Devices
Logo Analog Devices
Description Dual DCL
Datasheet ADATE206 DatasheetADATE206 Datasheet (PDF)

www.DataSheet4U.com 500 MHz Dual DCL ADATE206 FEATURES Driver, comparator, and active load 500 MHz toggle rate Inhibit mode function Dynamic clamps Operating voltage range: −1.5 V to 6.5 V Output voltage swing: 200 mV to 8 V Four range adjustable slew rate True/complement data mode bit 100-lead TQFP package, exposed pad Low per channel power 1.4 W with load off 1.75 W with load programmed at 20 mA nominal Low leakage (<10 nA) in High-Z mode Driver 50 Ω output resistance 1 ns minimum pulse width.

  ADATE206   ADATE206



Document
www.DataSheet4U.com 500 MHz Dual DCL ADATE206 FEATURES Driver, comparator, and active load 500 MHz toggle rate Inhibit mode function Dynamic clamps Operating voltage range: −1.5 V to 6.5 V Output voltage swing: 200 mV to 8 V Four range adjustable slew rate True/complement data mode bit 100-lead TQFP package, exposed pad Low per channel power 1.4 W with load off 1.75 W with load programmed at 20 mA nominal Low leakage (<10 nA) in High-Z mode Driver 50 Ω output resistance 1 ns minimum pulse width for a 3 V step Load: −35 mA to +35 mA maximum current range 7 69 8 68 9 67 6 70 22 54 23 53 24 52 25 51 26 50 27 49 28 48 29 47 15 61 14 62 10 65 11 66 FUNCTIONAL BLOCK DIAGRAM VCC (18, 19, 57, 58, 77, 78, 89, 98, 99) NC (30, 46) SHIELDS (80, 82, 94, 96) VIT VIL VIH ADATE206 DR_INV DR_DATA_P DR_DATA_P_T DR_DATA_N_T DR_DATA_N DR_EN_P DR_EN_P_T DR_EN_N_T DR_EN_N VTEN LDEN CLAMPL CLAMPH LOGIC DRIVER 81 95 DUT APPLICATIONS Automatic test equipment Semiconductor test systems Board test systems Instrumentation and characterization equipment CVH COMP_H_P COMP_H_N CLLM COMP_L_P COMP_L_N 91 85 31 45 32 44 13 63 34 42 35 41 90 86 COMP_H GENERAL DESCRIPTION The ADATE206 is a complete, single-chip solution that performs the pin electronics functions of driver, comparator, and active load (DCL) for ATE applications. The active load can be powered down if not used. The driver is a proprietary design that features three active modes: data high mode, data low mode, and term mode, as well as an inhibit state. The driver has low leakage (<10 nA) in High-Z mode. The output voltage range is −1.5 V to +6.5 V to accommodate a wide variety of test devices. The ADATE206 supports four programmable Tr/Tf times for applications where slower edge rates are required. The edge rate selection is done via two static digital CMOS select bits. The input data to the driver can be inverted using a single CMOS logic bit. This feature can be used for system calibration or applications where complement input data is needed. COMP_L CVL IOL LOAD LOGIC VCOM 1 75 1x VIOL VIOH GNDREF 4 72 3 73 2 74 IOH TEMP SENSOR (5 DIODES) 88 TEMP 05738-001 VEE (16, 17, 33, 43, 59, 60, 84, 87, 92) GND (5, 12, 20, 21, 36, 40, 55, 56, 64, 71, 76, 79, 83, 93, 97,100) Figure 1. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2006 Analog Devices, Inc. All rights reserved. www.DataSheet4U.com ADATE206 TABLE OF CONTENTS Features ..........


ADATE205 ADATE206 1102B


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)