Document
www.DataSheet4U.com
tm
TE CH
T14L256A
SRAM
FEATURES
• High speed access time: 8/10/12/15ns(max.) • Low power consumption : Active 300 mW (typ.) • Single + 3.3 power supply • Fully static operation – No clock or refreshing required • All inputs and outputs directly LVTTL compatible • Common I/O capability • Available packages :28-pin 300 mil, SOJ and TSOP-I (forward type). • Output enable (OE ) available for very fast access
32K X 8 HIGH SPEED CMOS STATIC RAM
GENERAL DESCRIPTION
The T14L256A is a high speed, low power CMOS static RAM organized as 32,768 x 8 bits that operates on a single 3.3-volt power supply. This device is packaged in a standard 28-pin 300 mil SOJ or TSOP-I forward.
BLOCK DIAGRAM
Vcc → VSS →
A0 . . . A 14 CS OE WE CONTROL DATA I/O I/O 1 . . . I/O 8 DECODER CORE ARRAY
PIN CONFIGURATION
A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O1 I/O2 I/O3 Vss 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 Vcc WE A13 A8 A9 A11 OE A10 CS I/O8 I/O7 I/O6 I/O5 I/O4
SOJ
22 21 20 19 18 17 16 15
PIN DESCRIPTION
SYMBOL A0 - A14 I/O1 - I/O8
CS
WE OE
28 27 26 25 24 23 22 21 20 19 18 17 16 15 A10 CS I/O8 I/O7 I/O6 I/O5 I/O4 VSS I/O3 I/O2 I/O1 A0 A1 A2
OE A11 A9 A8 A13 WE VCC A14 A12 A7 A6 A5 A4 A3
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Vcc Vss
DESCRIPTION Address Inputs Data Inputs/Outputs Chip Select Inputs Write Enable Output Enable Power Supply Ground
TSOP-I
PART NUMBER EXAMPLES
T14L256A-8J T14L256A-8P PACKAGE SPEED SOJ 8ns TSOP-I 8ns
Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice.
P. 1
Publication Date: APR. 2001 Revision: E
DataSheet 4 U .com
www.DataSheet4U.com
tm
TE CH
T14L256A
DC CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS
PARAMETER Supply Voltage to Vss Potential Inputs to Vss Potential Power Dissipation Storage Temperature RATING -0.5 to + 4.6 -0.5 to Vcc +0.5 1.0 -60 to +150 UNIT V V W °C
RECOMMENDED OPERATING CONDITIONS
PARAMETER Supply Voltage Input Voltage, low Input Voltage, high Ambient Temperature SYM Vcc MIN Typ-5% -0.3 2.1 0 TYP 3.3 MAX Typ+5% 0.8 Vcc+0.3 70 UNIT V V V °C
VIL VIH TA
TRUTH TABLE
CS H L L L OE X H L X WE X H H L MODE Not Selected Output Disable Read Write I/O1- I/O8 High-Z High-Z Data Out Data In Vcc ISB, I SB1 Icc Icc Icc
OPERATING CHARACTERISTICS
(Vcc = 3.3V ± 5%, Vss = 0V, Ta = 0 to 70 ° C)
PARAMETER Input Leakage Current Output Leakage Current Output Low Voltage Output High Voltage Operating Power Supply Current Standby Power Supply Current SYM. I LI I LO TEST CONDITIONS Vin=Vss to Vcc VI/O=Vss to Vcc ,
OE =
CS = VIH or
MIN. -10 -10 2.4 -
TYP. -
MAX. UNIT +10 uA +10 uA 0.4 110 100 90 80 15 2 V V mA mA mA mA mA mA
VIH or
WE = V IL
VOL VOH
Icc
ISB I SB1
8 10 Cycle = MIN. 12 Duty = 100% 15 CS = VIH , Cycle=MIN, Duty=100%
I OL = + 8.0mA I OH = - 4.0mA CS = VIL, I/O=0mA
CS ≥ Vcc -0.2V
Note: Typical characteristics are at Vcc = 3.3V, Ta = 25 °C
Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice.
P. 2
Publication Date: APR. 2001 Revision: E
DataSheet 4 U .com
www.DataSheet4U.com
tm
TE CH
T14L256A
CAPACITANCE
(Vcc = 3.3V, Ta = 25° C, f = 1 MHz)
PARAMETER Input Capacitance Input/ Output Capacitance SYMBOL CONDITION VIN = 0V VOUT= 0V MAX. 6 8 UNIT pF pF
CIN CI /O
Note: These parameters are sampled but not 100% tested.
AC TEST CONDITIONS
PARAMETER Input Pulse Levels Input Rise and Fall Times Input and Output Timing Reference Level Output Load CONDITIONS 0V to 3V 3 ns 1.5V C L =30pF,I OH / I OL = -4mA/8mA
AC TEST LOADS AND WAVEFORM
R1 320 ohm 3.3V OUTPUT 30pF Including Jig and Scope R2 350 ohm 5pF Including Jig and Scope R2 350 ohm R1 320 ohm
3.3V OUTPUT
(For TCLZ, TOLZ, TCHZ, TOHZ, TWHZ , TOW )
3.0V 0V 3ns
90% 10% 10%
90%
3ns
Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice.
P. 3
Publication Date: APR. 2001 Revision: E
DataSheet 4 U .com
www.DataSheet4U.com
tm
TE CH
T14L256A
AC CHARACTERISTICS
(Vcc =3.3V ± 5%, Vss = 0V, Ta = 0 to 70°C)
(1) READ CYCLE
T14L256A-8 T14L256A-10 T14L256A-12 T14L256A-1 UNIT
PARAMETER Read Cycle Time Address Access Time Chip Select Access Time Output Enable to Output Valid Chip Selection to Output in Low Z Output Enable to Output in Low Z Chip Deselection to Output in High Z Output Disable to Output in High Z Output Hold from Address Change
SYM.
MIN. MAX. MIN. MAX. MIN. MAX.
5
MIN. MAX.
tRC tAA tACS tAOE tCLZ* tOLZ tCHZ* tOHZ tOH
8 3 0 2.5
8 8 5 4 4 -
10 3 0 3
10 10 6 5 5 -
12 3 0 3
12 12 7 6 6 -
15 3 0 0 0 3
15 15 7 7 7 -
ns ns ns ns ns ns ns ns ns
* These parameters are sampled but not 100% tested.
(2)WRITE CYCLE
PARAMETER Write Cycle Time Chip Selection to End of Write Address Valid to End of Write Address Setup Time Write Pulse Width Write Recovery Time Data Valid to End of Write Data Hold from End of Write Write to Output in High Z Output Disable to Output in High Z Output Active from End of Write SYM.
T14L256A-8 T14L256A-10 T1.