DatasheetsPDF.com

ST1331 Dataheets PDF



Part Number ST1331
Manufacturers ST Microelectronics
Logo ST Microelectronics
Description (ST1331/1333/1353) 6-Contact Memory Card IC 272-bit EEPROM
Datasheet ST1331 DatasheetST1331 Datasheet (PDF)

ST1331, ST1333 ST1353 6-Contact Memory Card IC 272-bit EEPROM with Advanced Security Mechanisms DATA BRIEFING s s s s s s s s s s 5 V Single Supply Voltage Counting Capability (two options) – up to 32767 (85 -1) – 8 times reloadable, up to 4095 (84-1) Active Authentication Function (ST1333/1353) Cipher Block Chaining Function (ST1353) Memory Divided into : – 16 bits of Circuit Identification – 48 bits of Card Identification – 40 bits of Count Data – 16 bits for Validation Certificate – 24 bit.

  ST1331   ST1331



Document
ST1331, ST1333 ST1353 6-Contact Memory Card IC 272-bit EEPROM with Advanced Security Mechanisms DATA BRIEFING s s s s s s s s s s 5 V Single Supply Voltage Counting Capability (two options) – up to 32767 (85 -1) – 8 times reloadable, up to 4095 (84-1) Active Authentication Function (ST1333/1353) Cipher Block Chaining Function (ST1353) Memory Divided into : – 16 bits of Circuit Identification – 48 bits of Card Identification – 40 bits of Count Data – 16 bits for Validation Certificate – 24 bits of Transport Code – 64 bits of Issuer Data (ST1331) or Authentication Secret Key (ST1333/1353) – 32 bits of Anti-tearing Flags (optional) – 56 bits of User data (optionally not erasable) 1 Million Erase/Write Cycle (minimum) 10 Year Data Retention (minimum) 3.5 ms Programming Time at 5 V (typical) 500 µA Supply Current at 5 V (typical) 250 µA Stand-by Current at 5 V (typical) 1 Micromodule (D10) 1 1 1 Wafer DESCRIPTION The members of the ST1331/1333/1353 family are principally designed for use in prepaid Phonecard applications. Each is a 272-bit EEPROM device, with associated security logic and special fuses to control memory access. The memory is arranged as a matrix of 34 x 8 cells, accessed in a serial bitwise fashion for reading and programming, and in Table 1. Signal Names CLK RST Function code B I/O VCC GND Data Input / Output Supply Voltage Clock Figure 1. Logic Diagram VCC RST B ST1331 ST1333 ST1353 I/O CLK GND Ground AI03105b October 1999 Complete data available under NDA. 1/3 ST1331, ST1333, ST1353 Figure 2. Memory Map 16 masked bits Circuit Identification Area Card Identification Area (ID) 0 16 Physical EEPROM Cells 32 bits RAM1 (Write-Only) (RN) (ST1333, ST1353) 0 32 48 bits Data Area (CD) 40 bits 8 bits 16 bits (Counters and Transport Code) Reserved Area (RA) Certificate (CER) Issuer-Defined Area (ST1331) 64 bits Authentication Secret Key (SK) (ST1333, ST1353) 64 104 112 128 Physical EEPROM Cells 192 Reserved Area (RA) 256 260 264 288 Physical EEPROM Cells 32 bits Anti-Tearing Flags 320 4 bits 4 bits 24 bits Signature Fuses Unused 56 bits User-Defined Area 376 AI03384 Note: 1. The write-only RAM area (RN) is applicable only for the User Configuration. a byte-wise fashion for internal erasing. An on-chip address counter provides an internal address space of up to 512 bits. Each member of the ST1331/1333/1353 family has an identification data area, unit-counters (with an anti-tearing mechanism for reliable usage in open readers), a post validation certificate, an issuer area (ST1331) or an authentication secret key area (ST1333/1353), and a user area. This is summarized in Figure 2. The validation certificate allows the recognition of the device by the appropriate security module. The anti-tearing mechanism guards against extra, spurious count signals being executed when the 2/3 ST1331, ST1333, ST1353 card is unexpectedly extracted, while an operation is underway, in an open reader. OPTIONS Three options can be chosen on ordering the device: – The anti-tearing mechanism can be disconnected. In this case, the anti-tearing flag area from bit 288d to bit 319d is unused (Figure 2). – The user area, from bit 320d to bit 375d, can be defined as “not erasable” in the User Configuration. – The reload mechanism can be activated. In this case, erasing a bit in the reload counter refreshes the certificate (CER). At this time, the certificate can be programmed with a new value. ORDERING INFORMATION The notation used for the device number is as shown in Table 2. For a list of available options (speed, package, etc.) or for further information on any aspect of this device, please contact your nearest ST Sales Office. EXTERNAL COMMANDS The device uses six contacts: VCC, GND, I/O, CLK, RST, B. Four commands distinct can be composed using these external pins: – RESET: to reset the internal address register to 000d – READ: to increment the internal address register and read the data bit at the new address – COMPARE: to allow comparison of the presented code against the internal transport code – PROGRAM: to program the bit at the current address CONFIGURATIONS The device works in two distinct configurations: – Issuer Configuration: for the card manufacturer. Customized data can be written to the chip, to initialize it before release to the end user. – User Configuration: for use by the end user of the card, but with restricted access. Table 2. Ordering Information Scheme Example: ST1333 – C W4 / XX YY Product 31 33 53 Issuer Area Active Authentication Function Cipher Block Chaining Authentication Function Transport Code Given by ST Customer Code Given by the Issuer Fuse Blow Voltage B C 6 V1 5 V1 D10 W4 W2 Note: 1. Please contact your nearest ST Sales Office to check on availability Delivery Form Micromodule on reel Wafer (180 µm thickness) Wafer (280 µm thickness) 3/3 .


SAFC166 ST1331 ST1333


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)