Document
UF1000F THRU UF1008F
ULTRAFAST SWITCHING RECTIFIER VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes
FEATURES l Plastic package has Underwriters Laboratory Flammability Classification 94V-O Utilizing l l l l l Flame Retardant Epoxy Molding Compound Exceeds environmental standards of MIL-S-19500/228 Low power loss, high efficiency Low forward voltage, high current capability High surge capacity Ultra Fast recovery times, high voltage ITO-220AC
MECHANICAL DATA Case: ITO-220AC full molded plastic package Terminals: Lead solderable per MIL-STD-202, Method 208 Polarity: As marked Mounting Position: Any Weight: 0.08 ounce, 2.24 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ¢J ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20% TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375”(9.5mm) lead length @ TC=100 ¢J Peak Forward Surge Current, 8.3ms single half sine wave superimposed on rated load(JECEC method) Maximum Instantaneous Forward Voltage at 10.0A Maximum DC Reverse Current @TA=25 ¢J at Rated DC Blocking Voltage @TA=125 ¢J Maximum Reverse Recovery Time(Note 1) Typical Junction capacitance (Note 2) Typical Junction Resistance (Note 2) R £K JA Operating and Storage Temperature Range TJ,TSTG
UF1000F UF1001F UF1002F UF1003F UF1004F UF1006F UF1008F UNITS
50 35 50
100 70 100
200 140 200
300 210 300 10.0 150
400 280 400
600 420 600
800 560 800
V V V A A
1.0 10.0 500 50 80
1.3
1.7
V £g A £g A ns PF ¢J /W ¢J
100 50 15 -50 to +150
NOTES: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1A, Irr=0.25A 2. Measured at 1 MHz and applied reverse voltage of 4.0 VDC 3. Thermal resistance from junction to ambient and from junction to lead length 0.375"(9.5mm) P.C.B. mounted
RATING AND CHARACTERISTIC CURVES UF1000F THRU UF1008F
trr
+0.5A 0 -0.25
NOTE:1.Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF 2.Rise Time = 10ns max. Source Impedance = 50 Ohms
-1.0
SET TIME BASE FOR 50 ns/cm
1cm
Fig. 1-REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
PEAK FORWARD CURRENT, AMPERES
20
12 8 4 0 0 50 100 150
INSTANTANEOUS REVERSE CURRENT, MICROAMPERES
16
1000
TJ = 125 ¢J 100
10
CASE TEMPERATURE, ¢J
Fig. 1-TYPICAL FORWARD CURRENT DERATING CURVE
PEAK FORWARD CURRENT AMPERES
150 120 90 60 30 TJ = 125 ¢J 8.3ms SINGLE HALF SINCEWAVE JEDEC METHOD
TJ = 25 ¢J 1.0
0.1 20 40 60 80 100 120 140
PERCENT OF RATED PEAK REVERSE VOLTAGE
Fig. 2-TYPICAL REVERSE CHARACTERISTICS
80 40 1 2 5 10 20 50 100 20 UF1000F 10 3.0 UF1008F
NUMBER OF CYCLES AT 60Hz
Fig. 3-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT
210
INSTANTANEOUS FORWARD CURRENT, (A)
1.0 0.3
CAPACITANCE, (pF)
200 160 120 80 40 UF1008F 0 1 2 5 20 50 100 200 500 UF1000F
0.1
0.03 0.01 0.4
0.6
0.8
1.0
1.2
1.4
1.8
REVERSE VOLTAGE, VOLTS
FORWARD VOLTAGE, VOLTS
Fig. 4-TYPICA.