DatasheetsPDF.com

MBM29LV160B Dataheets PDF



Part Number MBM29LV160B
Manufacturers Fujitsu Media Devices
Logo Fujitsu Media Devices
Description 16M (2M x 8/1M x 16) BIT FLASH MEMORY
Datasheet MBM29LV160B DatasheetMBM29LV160B Datasheet (PDF)

FUJITSU SEMICONDUCTOR DATA SHEET DS05-20846-4E FLASH MEMORY CMOS 16M (2M × 8/1M × 16) BIT MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s FEATURES • Single 3.0 V read, program and erase Minimizes system level power requirements • Compatible with JEDEC-standard commands Uses same software commands as E2PROMs • Compatible with JEDEC-standard world-wide pinouts 48-pin TSOP (I) (Package suffix: PFTN-Normal Bend Type, PFTR-Reversed Bend Type) 46-pin SON (Package suffix: PN) 48-pin CSOP (Package su.

  MBM29LV160B   MBM29LV160B



Document
FUJITSU SEMICONDUCTOR DATA SHEET DS05-20846-4E FLASH MEMORY CMOS 16M (2M × 8/1M × 16) BIT MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s FEATURES • Single 3.0 V read, program and erase Minimizes system level power requirements • Compatible with JEDEC-standard commands Uses same software commands as E2PROMs • Compatible with JEDEC-standard world-wide pinouts 48-pin TSOP (I) (Package suffix: PFTN-Normal Bend Type, PFTR-Reversed Bend Type) 46-pin SON (Package suffix: PN) 48-pin CSOP (Package suffix: PCV) 48-ball FBGA (Package suffix: PBT) • Minimum 100,000 program/erase cycles • High performance 80 ns maximum access time • Sector erase architecture One 8K word, two 4K words, one 16K word, and thirty-one 32K words sectors in word mode One 16K byte, two 8K bytes, one 32K byte, and thirty-one 64K bytes sectors in byte mode Any combination of sectors can be concurrently erased. Also supports full chip erase • Boot Code Sector Architecture T = Top sector B = Bottom sector • Embedded EraseTM Algorithms Automatically pre-programs and erases the chip or any sector • Embedded programTM Algorithms Automatically programs and verifies data at specified address • Data Polling and Toggle Bit feature for detection of program or erase cycle completion • Ready/Busy output (RY/BY) Hardware method for detection of program or erase cycle completion • Automatic sleep mode When addresses remain stable, automatically switches themselves to low power mode • Low VCC write inhibit ≤ 2.5 V (Continued) Embedded EraseTM and Embedded ProgramTM are trademarks of Advanced Micro Devices, Inc. MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 (Continued) • Erase Suspend/Resume Suspends the erase operation to allow a read data and/or program in another sector within the same device • Sector protection Hardware method disables any combination of sectors from program or erase operations • Sector Protection set function by Extended sector Protect command • Temporary sector unprotection Temporary sector unprotection via the RESET pin • In accordance with CFI (Common Flash Memory Interface) s PACKAGE 48-pin plastic TSOP (I) Marking Side 46-pin plastic SON Marking Side (FPT-48P-M19) (FPT-48P-M20) (LCC-46P-M02) 48-pin plastic CSOP 48-pin plastic FBGA (LCC-48P-M03) (BGA-48P-M03) (BGA-48P-M13) 2 MBM29LV160T-80/-90/-12/MBM29LV160B-80/-90/-12 s GENERAL DESCRIPTION The MBM29LV160T/B is a 16M-bit, 3.0 V-only Flash memory organized as 2M bytes of 8 bits each or 1M words of 16 bits each. The MBM29LV160T/B is offered in a 48-pin TSOP (I), 46-pin SON, 48-pin CSOP and 48-ball FBGA packages. The device is designed to be programmed in-system with the standard system 3.0 V VCC supply. 12.0 V VPP and 5.0 V VCC are not required for write or erase operations. The device can also be reprogrammed in standard EPROM programmers. The standard MBM29LV160T/B offers access times of 80 ns and 120 ns, allowing operation of high-speed microprocessors without wait states. To eliminate bus contention the device has separate chip enable (CE), write enable (WE), and output enable (OE) controls. The MBM29LV160T/B is pin and command set compatible with JEDEC standard E2PROMs. Commands are written to the command register using standard microprocessor write timings. Register contents serve as input to an internal state-machine which controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the device is similar to reading from 5.0 V and 12.0 V Flash or EPROM devices. The MBM29LV160T/B is programmed by executing the program command sequence. This will invoke the Embedded Program Algorithm which is an internal algorithm that automatically times the program pulse widths and verifies proper cell margins. Typically, each sector can be programmed and verified in about 0.5 seconds. Erase is accomplished by executing the erase command sequence. This will invoke the Embedded Erase Algorithm which is an internal algorithm that automatically preprograms the array if it is not already programmed before executing the erase operation. During erase, the device automatically times the erase pulse widths and verifies proper cell margins. Any individual sector is typically erased and verified in 1.0 second. (If already preprogrammed.) The device also features a sector erase architecture. The sector mode allows each sector to be erased and reprogrammed without affecting other sectors. The MBM29LV160T/B is erased when shipped from the factory. The device features single 3.0 V power supply operation for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. A low VCC detector automatically inhibits write operations on the loss of power. The end of program or erase is detected by Data Polling of DQ7, by the Toggle Bit feature on DQ6, or the RY/BY output pin. Once the end of a program or erase cycle has been comlete.


MBM29LV200TC MBM29LV160B MBM29LV160T


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)