DatasheetsPDF.com

MC145201 Dataheets PDF



Part Number MC145201
Manufacturers Motorola
Logo Motorola
Description 2.0 GHz PLL Frequency Synthesizers
Datasheet MC145201 DatasheetMC145201 Datasheet (PDF)

MOTOROLA SEMICONDUCTOR TECHNICAL DATA Order this document by MC145200/D 2.0 GHz PLL Frequency Synthesizers MC145200 MC145201 Include On–Board 64/65 Prescalers The MC145200 and MC145201 are single–package synthesizers with serial interfaces capable of direct usage up to 2.0 GHz. A special architecture makes these PLLs very easy to program because a byte–oriented format is utilized. Due to the patented BitGrabber™ registers, no address/steering bits are required for random access of the three.

  MC145201   MC145201


Document
MOTOROLA SEMICONDUCTOR TECHNICAL DATA Order this document by MC145200/D 2.0 GHz PLL Frequency Synthesizers MC145200 MC145201 Include On–Board 64/65 Prescalers The MC145200 and MC145201 are single–package synthesizers with serial interfaces capable of direct usage up to 2.0 GHz. A special architecture makes these PLLs very easy to program because a byte–oriented format is utilized. Due to the patented BitGrabber™ registers, no address/steering bits are required for random access of the three registers. Thus, tuning can be accomplished via a 3–byte serial transfer to the 24–bit A register. The interface is both SPI and MICROWIRE™ compatible. Each device features a single–ended current source/sink phase detector output and a double–ended phase detector output. Both phase detectors have linear transfer functions (no dead zones). The maximum current of the single–ended phase detector output is determined by an external resistor tied from the Rx pin to ground. This current can be varied via the serial port. The MC145200 features logic–level converters and high–voltage phase/ frequency detectors; the detector supply may range up to 9.5 V. The MC145201 has lower–voltage phase/frequency detectors optimized for single–supply systems of 5 V ± 10%. Each part includes a differential RF input which may be operated in a single–ended mode. Also featured are on–board support of an external crystal and a programmable reference output. The R, A, and N counters are fully programmable. The C register (configuration register) allows the parts to be configured to meet various applications. A patented feature allows the C register to shut off unused outputs, thereby minimizing system noise and interference. In order to have consistent lock times and prevent erroneous data from being loaded into the counters, on–board circuitry synchronizes the update of the A register if the A or N counters are loading. Similarly, an update of the R register is synchronized if the R counter is loading. The double–buffered R register allows new divide ratios to be presented to the three counters (R, A, and N) simultaneously. • Maximum Operating Frequency: 2000 MHz @ Vin = 200 mV p–p • Operating Supply Current: 12 mA Nominal • Operating Supply Voltage Range (VDD and VCC Pins): 4.5 to 5.5 V • Operating Supply Voltage Range of Phase Detectors (VPD Pin) — MC145200: 8.0 to 9.5 V MC145201: 4.5 to 5.5 V • Current Source/Sink Phase Detector Output Capability: 2 mA Maximum • Gain of Current Source/Sink Phase/Frequency Detector Controllable via Serial Port • Operating Temperature Range: – 40 to + 85°C • R Counter Division Range: (1 and) 5 to 8191 • Dual–Modulus Capability Provides Total Division up to 262,143 • High–Speed Serial Interface: 4 Mbps • OUTPUT A Pin, When Configured as Data Out, Permits Cascading of Devices • Two General–Purpose Digital Outputs — OUTPUT A: Totem–Pole (Push–Pull) OUTPUT B: Open–Drain • Power–Saving Standby Feature with Orderly Recovery for Minimizing Lock Times, Standby Current: 30 µA • Evaluation Kit Available (Part Numbers MC145200EVK and MC145201EVK) • See Application Note AN1253/D for Low–Pass Filter Design, and AN1277/D for Offset Reference PLLs for Fine Resolution or Fast Hopping 20 F SUFFIX SOG PACKAGE CASE 751J 1 20 1 DT SUFFIX TSSOP CASE 948D ORDERING INFORMATION MC145200F MC145201F MC145200DT MC145201DT SOG Package SOG Package TSSOP TSSOP PIN ASSIGNMENT REFout LD φR φV VPD PDout GND Rx TEST 1 fin 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 REFin Din CLK ENB OUTPUT A OUTPUT B VDD TEST 2 VCC fin BitGrabber is a trademark of Motorola, Inc. MICROWIRE is a trademark of National Semiconductor Corp. REV 4 1/98 TN98012300 © Motorola, Inc. 1998 MOTOROLA MC145200•MC145201 1 BLOCK DIAGRAM DATA OUT REFin 20 OSC OR 4–STAGE DIVIDER (CONFIGURABLE) 3 13–STAGE R COUNTER fR PORT fV 13 DOUBLE–BUFFERED BitGrabber™ R REGISTER 16 BITS SELECT LOGIC 16 OUTPUT A REFout 1 LOCK DETECTOR AND CONTROL 2 LD CLK Din 18 19 SHIFT REGISTER AND CONTROL LOGIC BitGrabber™ C REGISTER 8 BITS 8 PHASE/FREQUENCY DETECTOR A AND CONTROL 6 Rx 24 PDout ENB 17 STANDBY LOGIC POR 2 PHASE/FREQUENCY DETECTOR B AND CONTROL 3 φ R 4 φV BitGrabber™ A REGISTER 24 BITS INTERNAL CONTROL 6 4 6–STAGE A COUNTER 12 12–STAGE N COUNTER 15 OUTPUT B (OPEN–DRAIN OUTPUT) fin fin 11 10 INPUT AMP 64/65 PRESCALER MODULUS CONTROL LOGIC 13 TEST 2 9 TEST 1 SUPPLY CONNECTIONS: PIN 12 = VCC (V+ TO INPUT AMP AND 64/65 PRESCALER) PIN 5 = VPD (V+ TO PHASE/FREQUENCY DETECTORS A AND B) PIN 14 = VDD (V+ TO BALANCE OF CIRCUIT) PIN 7 = GND (COMMON GROUND) MAXIMUM RATINGS* (Voltages Referenced to GND, unless otherwise stated) Symbol VCC, VDD VPD Vin Vout Vout Iin, IPD Iout IDD PD Tstg TL Parameter DC Supply Voltage (Pins 12 and 14) DC Supply Voltage (Pin 5) DC Input Voltage DC Output Voltage (except OUTPUT B, PDout, φR, φV) DC Output Voltage (OUTPUT B, PDout, φR, φV) DC Input Current, per Pin (Includes VPD) DC Output Current, per Pin DC Supply Current, VDD and GND.


MC145202 MC145201 MC145200


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)