DatasheetsPDF.com

DFC10E Dataheets PDF



Part Number DFC10E
Manufacturers Power-One
Logo Power-One
Description SINGLE OUTPUT
Datasheet DFC10E DatasheetDFC10E Datasheet (PDF)

DFC10 SERIES SINGLE OUTPUT DESCRIPTION The DFC10 Series provides power converter solutions to meet commercial and industrial requirements. With power densities above 11 watts per cubic inch (0.67 watts per cm3), overcurrent protection, and five-sided shielded case, the DFC10 meets the most rigorous needs in an industry standard case size. The 220KHz operating frequency of the DFC10 Series allows an increased power density while including adequate heat sinking and input/output filtering. This eli.

  DFC10E   DFC10E



Document
DFC10 SERIES SINGLE OUTPUT DESCRIPTION The DFC10 Series provides power converter solutions to meet commercial and industrial requirements. With power densities above 11 watts per cubic inch (0.67 watts per cm3), overcurrent protection, and five-sided shielded case, the DFC10 meets the most rigorous needs in an industry standard case size. The 220KHz operating frequency of the DFC10 Series allows an increased power density while including adequate heat sinking and input/output filtering. This eliminates the need for external components in most applications. Full overload protection is provided by pulse-by-pulse current limiting. FEATURES • High Power Density, up to 11 Watts per Cubic Inch (0.67 watts per cm3) • Efficiencies to 83% (Lower for 3.3V) • Low Input to Output Capacitance • 700V Isolation(1544V for 48V Converters) • Continuous Overcurrent Protection • 3.3Volt Output Available • Five-Side Shielded Copper Case • Extended Input Range (2:1) BOTTOM VIEW 2.02 (51.31) 0.300 (7.62) 0.000 0.200 (5.08) 0.500 (12.70) 0.61 (15.5) 0.61 (15.5) 0.000 1 2 5 3 SIDE VIEW 0.040 (1.02) DIA TYP 1.02 (25.91) 0.800 (20.32) Mechanical tolerances unless otherwise noted: X.XX dimensions: ±0.020 inches X.XXX dimensions: ±0.005 inches NOTES (1) All parameters measured at Tc = 25°C, nominal input voltage and full rated load unless otherwise noted. Refer to the Technical Reference Section for the definition of terms, measurement circuits and other information. The Case is tied to the -Input pin. The functional temperature range is intended to give an additional data point for use in evaluating this power supply. At the low functional temperature the power supply will function with no side effects, however, sustained operation at the high functional temperature will reduce expected operational life. The data sheet specifications are not guaranteed beyond the case operating range. The case thermal impedance is specified as the case temperature rise over ambient per package watt dissipated. (2) (3) (4) Rev. 04/2000 1 0.42 (10.67) 0.3 (7.62) 0.000 DFC10 SERIES – SINGLE OUTPUT NOTES (1) All parameters measured at Tc = 25°C, nominal input voltage and full rated load unless otherwise noted. Refer to the Technical Reference Section for the definition of terms, measurement circuits and other information. Noise is measured per Technical Reference Section. Measurement bandwidth is 0-20 MHz for peak-peak measurements, 10 kHz to 1 MHz for RMS measurements. Output noise is measured with a 0.01µF / 100V ceramic capacitor in parallel with a 1µf / 35V Tantalum capacitor, 1 inch from the output pins to simulate standard PCB decoupling capacitance. Short term stability is specified after a 30 minute warmup at full load, constant line and recording the drift over a 24 hour period. The input ripple rejection is specified for DC to 120 Hz ripple with a modulation amplitude of 1% of Vin. greater than 0.25 ohms. Input capacitors with an ESR less than 0.25 ohms may cause peaking.


DFB5435 DFC10E DFC10E12S12


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)