DatasheetsPDF.com

MK3754 Dataheets PDF



Part Number MK3754
Manufacturers Integrated Circuit Systems
Logo Integrated Circuit Systems
Description Low Cost 54 MHz 3.3 Volt VCXO
Datasheet MK3754 DatasheetMK3754 Datasheet (PDF)

I C R O C LOC K Description The MK3754 is ICS/Microclock’s lowest cost, low jitter, high performance 3.3 Volt VCXO and PLL clock synthesizer designed to replace expensive 54 MHz VCXOs. The on-chip Voltage Controlled Crystal Oscillator accepts a 0 to 3.3 V input voltage to vary the output clocks by ±100 ppm. Using ICS/Microclock’s patented VCXO and analog/digital Phase-Locked Loop (PLL) techniques, the device uses an inexpensive external 13.5 MHz pullable crystal input to produce a 54 MHz output .

  MK3754   MK3754


Document
I C R O C LOC K Description The MK3754 is ICS/Microclock’s lowest cost, low jitter, high performance 3.3 Volt VCXO and PLL clock synthesizer designed to replace expensive 54 MHz VCXOs. The on-chip Voltage Controlled Crystal Oscillator accepts a 0 to 3.3 V input voltage to vary the output clocks by ±100 ppm. Using ICS/Microclock’s patented VCXO and analog/digital Phase-Locked Loop (PLL) techniques, the device uses an inexpensive external 13.5 MHz pullable crystal input to produce a 54 MHz output clock. The MK3754A is a drop-in replacement to the earlier MK3754S. MK3754 Low Cost 54 MHz 3.3 Volt VCXO Features • Packaged in 8 pin SOIC • 3.3 V only operating voltage • Uses an inexpensive 13.500 MHz external crystal • On-chip VCXO (patented) with pull range of 200ppm (minimum) • VCXO tuning voltage of 0 to 3.3 V • 12mA output drive capability at TTL levels • Advanced, low power, sub-micron CMOS process • The A version is the latest, manufactured in a smaller geometry process. The MK3754A gives a wider pull range than the MK3754S, and so is recommended for all new designs, and cost reductions of existing designs. Block Diagram VIN X1 13.5 MHz pullable crystal X2 Voltage Controlled Crystal Oscillator PLL/Clock Synthesis Circuitry Output Buffer 54MHz 1 Revision 060100 Printed 11/16/00 Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126• (408) 295-9800 tel • www.icst.com MDS 3754 D I C R O C LOC K Pin Assignment MK3754 X1 VDD VIN GND 1 2 3 4 MK3754 Low Cost 54 MHz 3.3 Volt VCXO 8 7 6 5 X2 GND CLK VDD 8 pin (150 mil) SOIC Pin Descriptions Number 1 2 3 4 5 6 7 8 Name X1 VDD VIN GND VDD CLK GND X2 Description Crystal connection. Connect to a pullable 13.5 MHz crystal. VDD. Connect to +3.3 V. Voltage input to VCXO. Zero to 3.3V analog input which controls the frequency of the VCXO. Connect to ground. VDD. Connect to +3.3 V. 54 MHz clock output. Connect to ground. Crystal connection. Connect to a pullable 13.5 MHz crystal. Pullable Crystal Specifications: Correlation (load) Capacitance C0/C1 ESR Operating Temperature Initial Accuracy Temperature plus Aging Stability 14 pF 240 max 35 Ω max 0 to 70 °C ±20 ppm ±50 ppm 2 Revision 060100 Printed 11/16/00 Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126• (408) 295-9800 tel • www.icst.com MDS 3754 D I C R O C LOC K Electrical Specifications Parameter Supply voltage, VDD Inputs and Clock Outputs Ambient Operating Temperature Soldering Temperature Storage temperature Operating Voltage, VDD Output High Voltage, VOH Output Low Voltage, VOL Output High Voltage, VOH, CMOS level Operating Supply Current, IDD Short Circuit Current VIN, VCXO control voltage Input Crystal Frequency Output Clock Rise Time Output Clock Fall Time Output Clock Duty Cycle Maximum Absolute Jitter, short term 54 MHz output pullability, note 2 Notes: Conditions MK3754 Low Cost 54 MHz 3.3 Volt VCXO Minimum Typical Maximum 7 VDD+0.5 70 260 150 3.45 0.4 Units V V °C °C °C V V V V mA mA V MHz ns ns % ps ppm ABSOLUTE MAXIMUM RATINGS (note 1) Referenced to GND Referenced to GND Max of 10 seconds -65 3.15 2.4 VDD-0.4 9 ±50 0 13.50000 0.8 to 2.0V 2.0 to 0.8V At 1.4V 0V ≤ VIN ≤ 3.3 V 1.5 1.5 60 3.3 -0.5 0 DC CHARACTERISTICS (VDD = 3.3 V unless noted) IOH=-12mA IOL=12mA IOH=-4mA No Load AC CHARACTERISTICS (VDD = 3.3 V unless noted) 40 ±100 50 100 1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged exposure to levels above the operating limits but below the Absolute Maximums may affect device reliability. 2. With an ICS approved pullable crystal. The A version has a typical range of ±180 ppm. External Components The MK3754 requires a minimum number of external components for proper operation. A decoupling capacitor of 0.01µF should be connected between VDD and GND on pins 2 and 4, as close to the MK3754 as possible. A series termination resistor of 33 Ω may be used for the clock output. The input crystal must be connected as close to the chip as possible. The input crystal should be a parallel mode, pullable, AT cut, 13.5 MHz, with 14 pF load capacitance. Consult ICS for recommended suppliers. IMPORTANT - read application note MAN05 before laying out the PCB. 3 Revision 060100 Printed 11/16/00 Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126• (408) 295-9800 tel • www.icst.com MDS 3754 D I C R O C LOC K MK3754 Low Cost 54 MHz 3.3 Volt VCXO Package Outline and Package Dimensions (For current dimensional specifications, see JEDEC Publication No. 95.) 8 pin SOIC Symbol A A1 E INDEX AREA H B C 1 2 h x 45° D D E e H h L Inches Min Max 0.0532 0.0688 0.0040 0.0098 0.0130 0.0200 0.0075 0.0098 0.1890 0.1968 0.1497 0.1574 .050 BSC 0.2284 0.2440 0.0099 0.0195 0.0160 0.0500 Millimeters Min Max 1.35 1.75 0.10 0.24 0.33 0.51 0.19 0.24 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.41 1.27 A1 e B C A L Ordering Information Part/Order Number MK3754A MK3754ATR MK.


MK3727 MK3754 MK41T56


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)