DatasheetsPDF.com

BTA208B Dataheets PDF



Part Number BTA208B
Manufacturers NXP
Logo NXP
Description Three quadrant triacs high commutation
Datasheet BTA208B DatasheetBTA208B Datasheet (PDF)

Philips Semiconductors Preliminary specification Three quadrant triacs high commutation GENERAL DESCRIPTION Glass passivated high commutation triacs in a plastic envelope intended for use in circuits where high static and dynamic dV/dt and high dI/dt can occur. These devices will commutate the full rated rms current at the maximum rated junction temperature without the aid of a snubber. BTA208B series C QUICK REFERENCE DATA SYMBOL VDRM IT(RMS) ITSM PARAMETER MAX. MAX. 600C 600 8 65 MAX. UNIT.

  BTA208B   BTA208B



Document
Philips Semiconductors Preliminary specification Three quadrant triacs high commutation GENERAL DESCRIPTION Glass passivated high commutation triacs in a plastic envelope intended for use in circuits where high static and dynamic dV/dt and high dI/dt can occur. These devices will commutate the full rated rms current at the maximum rated junction temperature without the aid of a snubber. BTA208B series C QUICK REFERENCE DATA SYMBOL VDRM IT(RMS) ITSM PARAMETER MAX. MAX. 600C 600 8 65 MAX. UNIT 800C 800 8 65 V A A BTA208- 500C Repetitive peak 500 off-state voltages RMS on-state current 8 Non-repetitive peak 65 on-state current PINNING - SOT404 PIN 1 2 3 mb DESCRIPTION main terminal 1 main terminal 2 gate main terminal 2 PIN CONFIGURATION mb SYMBOL T2 2 1 3 T1 G LIMITING VALUES Limiting values in accordance with the Absolute Maximum System (IEC 134). SYMBOL VDRM IT(RMS) ITSM PARAMETER Repetitive peak off-state voltages RMS on-state current Non-repetitive peak on-state current full sine wave; Tmb ≤ 102 ˚C full sine wave; Tj = 25 ˚C prior to surge t = 20 ms t = 16.7 ms t = 10 ms ITM = 12 A; IG = 0.2 A; dIG/dt = 0.2 A/µs CONDITIONS MIN. -500 5001 MAX. -600 6001 8 -800 800 UNIT V A I2t dIT/dt IGM VGM PGM PG(AV) Tstg Tj I2t for fusing Repetitive rate of rise of on-state current after triggering Peak gate current Peak gate voltage Peak gate power Average gate power Storage temperature Operating junction temperature - 65 71 21 100 2 5 5 0.5 150 125 A A A2s A/µs A V W W ˚C ˚C over any 20 ms period -40 - 1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may switch to the on-state. The rate of rise of current should not exceed 6 A/µs. October 1997 1 Rev 1.000 Philips Semiconductors Preliminary specification Three quadrant Triacs high commutation THERMAL RESISTANCES SYMBOL Rth j-mb Rth j-a PARAMETER CONDITIONS BTA208B series C MIN. - TYP. 55 MAX. 2.0 2.4 - UNIT K/W K/W K/W Thermal resistance full cycle junction to mounting base half cycle Thermal resistance minimum footprint, FR4 board junction to ambient STATIC CHARACTERISTICS Tj = 25 ˚C unless otherwise stated SYMBOL IGT PARAMETER Gate trigger current 2 CONDITIONS VD = 12 V; IT = 0.1 A T2+ G+ T2+ GT2- GT2+ G+ T2+ GT2- G- MIN. 2 2 2 0.25 - TYP. 1.3 0.7 0.4 0.1 MAX. 35 35 35 20 30 20 15 1.65 1.5 0.5 UNIT mA mA mA mA mA mA mA V V V mA IL Latching current VD = 12 V; IGT = 0.1 A IH VT VGT ID Holding current On-state voltage Gate trigger voltage Off-state leakage current VD = 12 V; IGT = 0.1 A IT = 10 A VD = 12 V; IT = 0.1 A VD = 400 V; IT = 0.1 A; Tj = 125 ˚C VD = VDRM(max); Tj = 125 ˚C DYNAMIC CHARACTERISTICS Tj = 25 ˚C unless otherwise stated SYMBOL dVD/dt dIcom/dt tgt PARAMETER Critical rate of rise of off-state voltage Critical rate of change of commutating current Gate controlled turn-on time CONDITIONS VDM = 67% VDRM(max); Tj = 125 ˚C; exponential waveform; gate open circuit VDM = 400 V; Tj = 125 ˚C; IT(RMS) = 8 A; without snubber; gate open circuit ITM = 12 A; VD = VDRM(max); IG = 0.1 A; dIG/dt = 5 A/µs MIN. 1000 3 TYP. 14 2 UNIT V/µs A/ms µs 2 Device does not trigger in the T2-, G+ quadrant. October 1997 2 Rev 1.000 Philips Semiconductors Preliminary specification Three quadrant triacs high commutation MECHANICAL DATA Dimensions in mm Net Mass: 1.4 g 10.3 max 4.5 max 1.4 max BTA208B series C 11 max 15.4 2.5 0.85 max (x2) 2.54 (x2) 0.5 Fig.1. SOT404 : centre pin connected to mounting base. Notes 1. Epoxy meets UL94 V0 at 1/8". MOUNTING INSTRUCTIONS Dimensions in mm 11.5 9.0 17.5 2.0 3.8 5.08 Fig.2. SOT404 : minimum pad sizes for surface mounting. Notes 1. Plastic meets UL94 V0 at 1/8". October 1997 3 Rev 1.000 Philips Semiconductors Preliminary specification Three quadrant Triacs high commutation DEFINITIONS Data sheet status Objective specification Product specification Limiting values BTA208B series C This data sheet contains target or goal specifications for product development. This data sheet contains final product specifications. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. © Philips Electronics N.V. 1997 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, .


BTA208-800F BTA208B BTA208B-500D


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)