DatasheetsPDF.com

IR21064PBF Dataheets PDF



Part Number IR21064PBF
Manufacturers International Rectifier
Logo International Rectifier
Description HIGH AND LOW SIDE DRIVER
Datasheet IR21064PBF DatasheetIR21064PBF Datasheet (PDF)

Data Sheet No. PD60162 Rev. W IR2106(4)(S) & (PbF) HIGH AND LOW SIDE DRIVER Features • Floating channel designed for bootstrap operation Fully operational to +600V Packages Tolerant to negative transient voltage dV/dt immune • Gate drive supply range from 10 to 20V (IR2106(4)) • Undervoltage lockout for both channels • 3.3V, 5V and 15V input logic compatible • Matched propagation delay for both channels • Logic and power ground +/- 5V offset. • Lower di/dt gate driver for better noise immu.

  IR21064PBF   IR21064PBF


Document
Data Sheet No. PD60162 Rev. W IR2106(4)(S) & (PbF) HIGH AND LOW SIDE DRIVER Features • Floating channel designed for bootstrap operation Fully operational to +600V Packages Tolerant to negative transient voltage dV/dt immune • Gate drive supply range from 10 to 20V (IR2106(4)) • Undervoltage lockout for both channels • 3.3V, 5V and 15V input logic compatible • Matched propagation delay for both channels • Logic and power ground +/- 5V offset. • Lower di/dt gate driver for better noise immunity • Outputs in phase with inputs (IR2106) • Also available LEAD-FREE 8-Lead SOIC 8-Lead PDIP 14-Lead SOIC 14-Lead PDIP Description 2106/2301//2108//2109/2302/2304Feature Comparison The IR2106(4)(S) are high voltage, high speed power MOSFET and IGBT drivers with independent high and low side referenced output channels. Proprietary HVIC and latch immune CMOS technologies enable ruggedized monolithic construction. The logic input is compatible with standard CMOS or LSTTL output, Part Input logic 2106/2301 21064 2108 21084 2109/2302 21094 2304 HIN/LIN HIN/LIN IN/SD HIN/LIN Crossconduction prevention logic no yes yes yes Dead-Time none Internal 540ns Programmable 0.54~5µs Internal 540ns Programmable 0.54~5µs Internal 100ns Ground Pins COM VSS/COM COM VSS/COM COM VSS/COM COM Ton/Toff 220/200 220/200 750/200 160/140 down to 3.3V logic. The output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high side configuration which operates up to 600 volts. Typical Connection VCC VCC VB HIN HIN HO LIN LIN VS COM LO IR2106 up to 600V TO LOAD up to 600V (Refer to Lead Assignments for correct pin configuration). This/These diagram(s) show electrical connections only. Please refer to our Application Notes and DesignTips for proper circuit board layout. HO VCC VCC VB HIN HIN VS LIN LIN VSS VSS COM LO IR21064 TO LOAD www.irf.com 1 IR2106(4)(S) & (PBF) Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. Symbol Definition Min. Max. Units VB VS VHO VCC VLO VIN VSS dVS/dt PD High side floating absolute voltage High side floating supply offset voltage High side floating output voltage Low side and logic fixed supply voltage Low side output voltage Logic input voltage Logic ground (IR21064 only) Allowable offset supply voltage transient Package power dissipation @ TA ≤ +25°C (8 lead PDIP) (8 lead SOIC) (14 lead PDIP) -0.3 VB - 25 VS - 0.3 -0.3 -0.3 VSS - 0.3 VCC - 25 — — — — 625 VB + 0.3 VB + 0.3 25 VCC + 0.3 VCC + 0.3 VCC + 0.3 50 1.0 0.625 1.6 V V/ns W (14 lead SOIC) — RthJA Thermal resistance, junction to ambient (8 lead PDIP) — (8 lead SOIC) — (14 lead PDIP) — 1.0 125 200 75 °C/W (14 lead SOIC) — 120 TJ Junction temperature TS Storage temperature TL Lead temperature (soldering, 10 seconds) — 150 -50 150 °C — 300 2 www.irf.com IR2106(4)(S & (PbF)) Recommended Operating Conditions The Input/Output logic timing diagram is shown in figure 1. For proper operation the device should be used within the recommended conditions. The VS and VSS offset rating are tested with all supplies biased at 15V differential. Symbol VB VS VHO VCC VLO VIN VSS TA Definition High side floating supply absolute voltage IR2106(4) High side floating supply offset voltage High side floating output voltage Low side and logic fixed supply voltage IR2106(4) Low side output voltage Logic input voltage Logic ground (IR21064 only) Ambient temperature Min. VS + 10 Note 1 VS 10 0 VSS -5 -40 Max. VS + 20 600 VB 20 VCC VCC 5 125 Units V °C Note 1: Logic operational for VS of -5 to +600V. Logic state held for VS of -5V to -VBS. (Please refer to the Design Tip DT97-3 for more details). Dynamic Electrical Characteristics VBIAS (VCC, VBS) = 15V, VSS = COM, CL = 1000 pF, TA = 25°C. Symbol ton toff MT tr tf Definition Turn-on propagation delay Turn-off propagation delay Delay matching, HS & LS turn-on/off Turn-on rise time Turn-off fall time Min. — — — — — Typ. 220 200 0 150 50 Max. Units Test Conditions 300 280 30 nsec 220 80 VS = 0V VS = 0V or 600V VS = 0V VS = 0V www.irf.com 3 IR2106(4)(S) & (PBF) Static Electrical Characteristics VBIAS (VCC, VBS) = 15V, VSS = COM and TA = 25°C unless otherwise specified. The VIL, VIH and IIN parameters are referenced to VSS/COM and are applicable to the respective input leads. The VO, IO and Ron parameters are referenced to COM and are applicable to the respective output leads: HO and LO. Symbol VIH VIL VOH VOL ILK IQBS IQCC IIN+ IIN- VCCUV+ VBSUV+ VCCUVVBSUVVCCUVH VBSUVH IO+ Definition Logic “1” inp.


IR2105S IR21064PBF IR21064SPBF


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)