Document
ES2A THRU ES2M
SURFACE MOUNT SUPER FAST RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 2.0 Amperes
DO-214AA (HSMB) (Round Lead)
H Cathode Band
J
AC
FEATURES
CCLeoaamsdepFlMiareanette.FrSiianelis:ehMo/RordoldehersidnCgPoilnmafsoptrliimca.natti(oUNnLo) tFel1a)m("mPa"Sbuiliftfyix designates
Classification Rating 94V-0 and MSL rating 1 Easy Pick And Place High Temp Soldering: 260°C for 10 Seconds At Terminals Ultrafast Recovery Times For High Efficiency
E F
G
DB
INCHES
DIMENSIONS MM
DIM MIN A .078 B .075 C .002 D ----E .035 F .065 G .205 H .160 J .130
MAX .116 .089 .008 .02 .055 .091 .224 .180 .155
MIN 1.98 1.90 .05 ----.90 1.65 5.21 4.06 3.30
MAX 2.95 2.25 .20 .51 1.40 2.32 5.69 4.57 3.94
NOTE
MECHANICAL DATA
Case: JEDEC DO-214AA molded plastic body over passivated chip Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight :0.005 ounce, 0.138 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%.
MDD Catalog Number
SYMBOLS ES2A ES2B ES2C ES2D ES2E ES2G ES2J ES2K ES2M
Maximum repetitive peak reverse voltage
VRRM 50 100 150 200 300 400 600 800 1000
Maximum RMS voltage
VRMS 35 70 105 140 210 280 420 560 700
Maximum DC blocking voltage
VDC 50 100 150 200 300 400 600 800 1000
Maximum average forward rectified current at TL=55 C
I(AV)
2.0
Peak forward surge current
8.3ms single half sine-wave superimposed on
IFSM
50.0
rated load (JEDEC Method)
Maximum instantaneous forward voltage at 2.0A
VF
0.975
1.35 1.7
Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=100 C
IR
5.0 150.0
Maximum reverse recovery time (NOTE 1)
trr
50
60 100
Typical junction capacitance (NOTE 2)
CJ
25.0
Typical thermal resistance (NOTE 3)
RθJA
Operating junction and storage temperature range TJ T, STG
20.0 -50 to +150
Note:1.Reverse recovery condition IF=0.5A,IR=1.0A,Irr=0.25A 2.Measured at 1MHz and applied reverse voltage of 4.0V D.C.
3.Pulse test: Pulse width 200 sec, Duty cycle 2%
4.High Temperature Solder Exemptions Applied, see EU Directive Annex 7.
MDD ELECTRONIC
UNITS VOLTS VOLTS VOLTS
Amps
Amps
Volts µA ns pF C/W C
RATINGS AND CHARACTERISTIC CURVES ES2A THRU ES2M
Figure 1 Typical Forward Characteristics
20
10 ES2G-2J
6 4 ES2A-2D
ES2K-2M
2
Amps 1 .6 .4
.2 .1 .06 .04
.02 .01
.4
.8 1.2 1.6 2.0 2.4 Volts
Instantaneous Forward Current - Amperes versus Instantaneous Forward Voltage - Volts
Figure 2 Forward Derating Curve 2.4
2.2
2.0
1.8 1.6
1.4
1.2 Amps
1.0
.8
.6
.4 Single Phase, Half Wave
.2 60Hz Resistive or Inductive Load
0 0
25 50 75 100 125 150
°C
Average Forward Rectified Current - Amperesversus Ambient Temperature -°C
Figure 3 Junction Capacitance
100 60 40
20 pF
10
6 4
2 1
.1
.2
.4
TJ=25°C
12 Volts
4
10 20 40
Junction Capacitance - pFversus Reverse Voltage - Volts
100 200 400
1000
MDD ELECTRONIC
RATINGS AND CHARACTERISTIC CURVES ES2A THRU ES2M
Figure 4 Peak Forward Surge Current
50
40
30 Amps
20
10
0 12
4 6 8 10 20 40 60 80 100
Cycles
Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles
Figure 5 New SMB Assembly
Round Lead Process
Figure 6 Reverse Recovery Time Characteristic And Test Circuit Diagram
50Ω 10Ω
25Vdc
1Ω
Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive
Pulse Generator
Note 2
Oscilloscope Note 1
+0.5A
0 -0.25
trr
-1.0
1cm Set Time Base for 20/100ns/cm
MDD ELECTRONIC
.