DatasheetsPDF.com

F1152NBGI Dataheets PDF



Part Number F1152NBGI
Manufacturers Integrated Device Technology
Logo Integrated Device Technology
Description RF to IF Dual Downconverting Mixer
Datasheet F1152NBGI DatasheetF1152NBGI Datasheet (PDF)

DATASHEET RF to IF Dual Downconverting Mixer GENERAL DESCRIPTION This document describes the specifications for the IDTF1152 Zero-DistortionTM RF to IF Downconverting Mixer. This device is part of a series of mixers offered with high side or low side injection options for all UTRA bands. See the Part# Matrix for the details of all devices in this series. The F1152 dual channel device is designed to operate with a single 5V supply. It is optimized for operation in a Multi-mode, Multi-carrier Ba.

  F1152NBGI   F1152NBGI


Document
DATASHEET RF to IF Dual Downconverting Mixer GENERAL DESCRIPTION This document describes the specifications for the IDTF1152 Zero-DistortionTM RF to IF Downconverting Mixer. This device is part of a series of mixers offered with high side or low side injection options for all UTRA bands. See the Part# Matrix for the details of all devices in this series. The F1152 dual channel device is designed to operate with a single 5V supply. It is optimized for operation in a Multi-mode, Multi-carrier BaseStation Receiver for RF bands from 1700 - 2200 MHz with Low Side Injection or from 1400 to 1700 MHz with High Side Injection. IF frequencies from 50 to 350 MHz are supported. Nominally, the device offers +43 dBm Output IP3 with 327 mA of ICC. Alternately one can adjust 4 resistor values and a toggle pin to run the device in low current mode with +40 dBm Output IP3 and 232 mA of ICC. COMPETITIVE ADVANTAGE In typical basestation receivers the RF to IF mixer dominates the linearity performance for the entire receive system. The Zero-DistortionTM family of mixers dramatically improve the maximum signal levels (IM3 tones) that the BTS can withstand at a desired Signal to Noise Ratio (SNR.) Alternately, one can run the device in Low Current Mode to reduce Power consumption significantly. Zero-DistortionTM technology allows realization of either benefit. IP3O: ⇑ 9 dB STD Mode, ⇑ 6 dB LC Mode Dissipation: ⇓ 40% LC Mode, ⇓ 12% STD Mode Allows for higher RF gain improving Sensitivity PART# MATRIX Part# F1100 F1102 F1150 F1152 F1162 RF freq range 698 - 915 698 - 915 1700 - 2200 1400 - 2200 2300 – 2700 UTRA bands 5,6,8,12,13,14,17 ,19,20 5,6,8,12,13,14,17 ,19,20 1,2,3,4,9,10, 33, 34,35, 36, 37,39 1,2,3,4,9,10,111, 211, 241, 33, 34,35, 36, 37,39 7,38,40,41 IF freq range 50 - 450 50 - 250 50 - 450 50 - 350 50 – 500 Typ. Gain 8.5 8.5 8.5 8.5 8.9 Injection High Side Both High Side Low Side Both 1 – with High side injection 1400 - 2200 MHz F1152NBGI FEATURES • Dual Path for Diversity Systems • Ideal for Multi-Carrier Systems • 8.5 dB Gain • Ultra linear +43 dBm IP3O • Low NF < 10 dB • 200 Ω output impedance • Ultra high +13 dBm P1dBI • Pin Compatible w/existing solutions • 6x6 36 pin package • Power Down mode • < 200 nsec settling from Power Down • Minimizes Synth pulling in Standby Mode • Low Current Mode : ICC = 232 mA • Standard Mode: ICC = 327 mA • NOTE production BOM on p. 20 DEVICE BLOCK DIAGRAM RFIN_A RF VCO RFIN_B IFOUT_A Bias Control STBY 2 LOISET LCMODE IFOUT_B ORDERING INFORMATION Omit IDT prefix 0.8 mm height package Tape & Reel IDTF1152NBGI8 RF product Line Green Industrial Temp range IDT Zero-DistortionTM Mixer 1 Rev1, June 2012 DATASHEET RF to IF Dual Downconverting Mixer ABSOLUTE MAXIMUM RATINGS VCC to GND STBY, LCMODE IF_A+, IF_B+, IF_A-, IF_B-, LO1_ADJ, LO2_ADJ LO_IN, LO_IN_ALT, RF_A, RF_B IF_BiasA, IF_BiasB to GND RF Input Power (RF_IN[A+, A-, B+, B-]) Continuous Power Dissipation θJA (Junction – Ambient) θJC (Junction – Case) The Case is defined as the exposed paddle Operating Temperature Range (Case Temperature) Maximum Junction Temperature Storage Temperature Range Lead Temperature (soldering, 10s) . 1400 - 2200 MHz F1152NBGI -0.3V to +5.5V -0.3V to (VCC_ + 0.3V) -0.3V to (VCC_ + 0.3V) -0.3V to +0.3V -0.3V to +0.3V +20dBm 2.2W +35°C/W +2.5°C/W TC = -40°C to +100°C 150°C -65°C to +150°C +260°C Stresses above those listed above may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. IDT Zero-DistortionTM Mixer 2 Rev1, June 2012 DATASHEET RF to IF Dual Downconverting Mixer 1400 - 2200 MHz F1152NBGI IDTF1152 SPECIFICATION Specifications apply at VCC = +5.00V, TC = +25°C FRF = 1850 MHz, FIF = 200MHz, PLO = 0 dBm, STBY = GND, LCMODE = VIH (STD Mode), EVKit BOM = Standard Mode, Transformer Loss included (not de-embedded) unless otherwise noted. Parameter Comment Symbol min typ max units Logic Input High For Standby, LCMODE Pins VIH 2 V Logic Input Low For Standby, LCMODE Pins VIL 0.8 V Logic Current For Standby, LCMODE Pins IIH, IIL -100 -20 µA Supply Voltage(s) All VCC pins VCC 4.75 to 5.25 V Operating Temperature Range Case Temperature TCASE -40 to +100 degC Supply Current Supply Current Supply Current RF Freq Range Total VCC , STD Mode Total Both Channels Total VCC , LC Mode LCMODE = GND EVkit BOM = LC Mode Total Both Channels Standby Mode STBY = VIH Total Both Channels Operating Range (low side injection) ISTD ILC ISTBY FRF 327 3801 mA 232 260 mA 17 1700 to 2200 26 mA MHz RF Freq Range Operating Range (hi-side inj. with RF match p. 20) 1400 1700 MHz IF Freq Range LO Freq Range Operating Range Low Side Injection FIF FLO 50 to 350 1350 to 2100 MHz MHz LO Power PLO -3 to +6 dBm RF Input Impedance .


IDT8N0Q001 F1152NBGI IDTF1178NBGI


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)