Document
RF to IF Dual Downconverting Mixer
GENERAL DESCRIPTION
This document describes the specifications for the IDTF1100 Zero-DistortionTM RF to IF Downconverting Mixer. This device is part of a series of downconverting mixers covering all UTRA bands. See the Part# Matrix for the details of all devices in the series.
The F1100 dual channel device operates with a single 5V supply. It is optimized for operation in a Multicarrier BaseStation Receiver for RF bands from 698 to 915 MHz with High Side Injection. IF frequencies from 150 to 450 MHz are supported. Nominally, the device offers +41 dBm Output IP3 with 350 mA of ICC.
COMPETITIVE ADVANTAGE
In typical basestation receivers the mixer limits the linearity performance for the entire receive system. The F1100 with Zero-Distortion technology dramatically improves the maximum IM3 interference that the BTS can withstand at a desired Signal to Noise Ratio (SNR.)
IP3O: ⇑ 7 dB
Allows for higher RF gain improving Sensitivity
PART# MATRIX
Part# F1100 F1102 F1150 F1152 F1162
RF freq range 698 - 915 400 - 1000 1700 - 2200
1400 - 2200
2300 – 2700
UTRA bands
5,6,8,12,13,14,17 ,19,20
5,6,8,12,13,14,17 ,19,20
1,2,3,4,9,10, 33, 34,35, 36, 37,39 1,2,3,4,9,10, 211, 241, 33, 34,35,
36, 37,39
7,38,40,41
IF freq range 150 - 450 50 - 300 50 - 450
50 - 350
50 – 500
Typ. Gain
9
Injection High Side
9.0 Both
8.5 High Side
8.5 Low Side
8.8 Both
1 – with High side injection
F1100
DATASHEET
698 - 915 MHz F1100NBGI
FEATURES
• Dual Path for Diversity Systems • Ideal for Multi-Carrier Systems • MIMO friendly: -6 dBm min LO drive • 9 dB Gain • Ultra linear: +41 dBm IP3O (350 MHz IF) • Low NF ~10 dB • 200 Ω output impedance • Ultra high +13 dBm P1dBI • Pin Compatible w/Existing solutions • 6x6 36 pin package • Power Down mode • Standard Mode: ICC = 350 mA
DEVICE BLOCK DIAGRAM
RFIN_A RF VCO RFIN_B
IFOUT_A
Bias Control
STBY 2
LOADJ
IFOUT_B
ORDERING INFORMATION
Omit IDT prefix
0.8 mm height package
Tape & Reel
IDTF1100NBGI8
RF product Line
Green
Industrial Temp range
IDT Zero-DistortionTM Mixer
1
RevO, Feb 2013
RF to IF Dual Downconverting Mixer
ABSOLUTE MAXIMUM RATINGS
VCC to GND STBY IF_A+, IF_B+, IF_A-, IF_B-, LO1_ADJ, LO2_ADJ LO_IN, LO_IN_ALT, RF_A, RF_B IF_BiasA, IF_BiasB to GND RF Input Power (RF_A, RF_B) Continuous Power Dissipation θJA (Junction – Ambient) θJC (Junction – Case) The Case is defined as the exposed paddle Operating Temperature Range (Case Temperature) Maximum Junction Temperature Storage Temperature Range Lead Temperature (soldering, 10s) .
F1100
DATASHEET
698 - 915 MHz F1100NBGI
-0.3V to +5.5V -0.3V to (VCC_ + 0.3V) -0.3V to (VCC_ + 0.3V) -0.3V to +0.3V -0.3V to +0.3V +20dBm 2.2W +35°C/W +2.5°C/W TC = -40°C to +100°C 150°C -65°C to +150°C +260°C
Stresses above those listed above may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to a.