Document
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
PXENPCAPTM-
Series
・Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte.
(ESR and rated ripple current values are improved from PXA series.)
・Rated voltage range : 2.5 to 16Vdc, Capacitance range : 33 to 2,700µF ・Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
・Solvent resistant type (see PRECAUTIONS AND GUIDELINES) ・RoHS Compliant ・Halogen Free
◆SPECIFICATIONS
PXF P34 Lower ESR
PXE
Lower ESR PXA P38
Items
Characteristics
Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current Dissipation Factor (tan ) Low Temperature Characteristics (Max. Impedance Ratio) Endurance
-55 to +105℃
2.5 to 16Vdc ±20% (M) Rated voltage×1.15 Shall not exceed values shown in STANDARD RATINGS.
(at 20℃, 120Hz) (at 105℃)
(at 20℃ after 2 minutes)
0.12 max.
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)≦1.15 Z(-55℃)/Z(+20℃)≦1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Bias Humidity
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at
60℃, 90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Surge Voltage
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Failure Rate
Leakage current
≦The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
◆MARKING
●Terminal Code : A
W
0.3max. L±0.3 (Note)
A±0.2
(Note) L±0.5 for HA0, HC0, JA0, JC0
Size Code φD L A B C
W
E61 5 5.8 5.3 5.3 5.9 0.5 to 0.8
F61 6.3 5.8 6.6 6.6 7.2 0.5 to 0.8
F80 6.3 7.7 6.6 6.6 7.2 0.5 to 0.8
H70 8 6.7 8.3 8.3 9.0 0.7 to 1.1
H80 8 7.7 8.3 8.3 9.0 0.7 to 1.1
HA0 8 10.0 8.3 8.3 9.0 0.7 to 1.1
HC0 8 12.0 8.3 8.3 9.0 0.7 to 1.1
J80 10 7.7 10.3 10.3 11.0 0.7 to 1.1
JA0 10 10.0 10.3 10.3 11.0 0.7 to 1.1
JC0 .
Similar Datasheet