DatasheetsPDF.com

SAMG53N Dataheets PDF



Part Number SAMG53N
Manufacturers Atmel
Logo Atmel
Description SMART ARM-based Flash MCU
Datasheet SAMG53N DatasheetSAMG53N Datasheet (PDF)

SAM G53G / SAM G53N Atmel | SMART ARM-based Flash MCU DATASHEET Description The Atmel® | SMART SAM G53 is a series of Flash microcontrollers based on the high-performance 32-bit ARM® Cortex®-M4 RISC processor. It operates at a maximum speed of 48 MHz and features up to 512 Kbytes of Flash and 96 Kbytes of SRAM. The peripheral set includes one USART, two UARTs, three I2C-bus interfaces (TWI), up to two SPIs, two three-channel general-purpose 16-bit timers, two I2S controllers with two-way, one-ch.

  SAMG53N   SAMG53N


Document
SAM G53G / SAM G53N Atmel | SMART ARM-based Flash MCU DATASHEET Description The Atmel® | SMART SAM G53 is a series of Flash microcontrollers based on the high-performance 32-bit ARM® Cortex®-M4 RISC processor. It operates at a maximum speed of 48 MHz and features up to 512 Kbytes of Flash and 96 Kbytes of SRAM. The peripheral set includes one USART, two UARTs, three I2C-bus interfaces (TWI), up to two SPIs, two three-channel general-purpose 16-bit timers, two I2S controllers with two-way, one-channel pulse density modulation, one realtime timer (RTT) and one 8-channel 12-bit ADC. The Atmel | SMART SAM G53 devices have two software-selectable low-power modes: Sleep and Wait. In Sleep mode, the processor is stopped while all other functions can be kept running. In Wait mode, all clocks and functions are stopped but some peripherals can be configured to wake up the system based on events, including partial asynchronous wake-up (SleepWalking™). The Event System allows peripherals to receive, react to and send events in Active and Sleep modes without processor intervention. A general-purpose microcontroller with the best ratio in terms of reduced power consumption, processing power and peripheral set, the SAM G53 series sustains a wide range of applications including consumer, industrial control, and PC peripherals. The device operates from 1.62V to 3.6V and is available in a 49-ball WLCSP package and a 100-pin LQFP package. Features  Core ̶ ARM Cortex-M4 up to 48 MHz ̶ Memory Protection Unit (MPU) ̶ DSP Instructions ̶ Floating Point Unit (FPU) ̶ Thumb®-2 instruction set  Memories ̶ 512 Kbytes embedded Flash ̶ 96 Kbytes embedded SRAM  System ̶ Embedded voltage regulator for single-supply operation Atmel-11240F-ATARM-SAM-G53G-SAM-G53N-Datasheet_24-Jul-15 ̶ Power-on reset (POR) and Watchdog for safe operation ̶ Quartz or ceramic resonator oscillators: 3 to 20 MHz with clock failure detection and 32.768 kHz for RTT or device clock ̶ High-precision 8/16/24 MHz factory-trimmed internal RC oscillator. In-application trimming access for frequency adjustment ̶ Slow clock internal RC oscillator as permanent Low-power mode device clock ̶ PLL range from 24 MHz to 48 MHz for device clock ̶ 28 peripheral DMA (PDC) channels ̶ 256-bit General-Purpose Registers (GPBR) ̶ 16 external interrupt lines  Power consumption in Active mode ̶ 102 µA/MHz running Fibonacci in SRAM  Low power modes (typical value) ̶ Wait mode down to 8 µA ̶ Wake-up time less than 5 µs ̶ Asynchronous partial wake-up (SleepWalking™) on UART and TWI  Peripherals ̶ One USART with SPI mode ̶ Two Inter-IC Sound Controllers (I2S) ̶ Two-way one-channel Pulse Density Modulation (PDM) (interfaces up to two microphones in PDM mode) ̶ Two UARTs ̶ Three Two-Wire Interface (TWI) modules featuring two TWI masters and one high-speed TWI slave ̶ One fast SPI at up to 24Mbit/s ̶ Two three-channel 16-bit Timer/Counters (TC) with Capture, Waveform, Compare and PWM modes ̶ One 32-bit Real-Time Timer (RTT)  I/O ̶ Up to 38 controllable I/O lines with external interrupt capability (edge or level sensitivity), debouncing, glitch filtering and on-die series resistor termination. Individually programmable open-drain, pull-up and pull-down resistor and synchronous output  Analog ̶ One 8-channel ADC, resolution up to 12 bits, sampling rate up to 800 kSps  Package ̶ 49-ball WLCSP ̶ 100-pin LQFP, 14 x 14 mm, pitch 0.5 mm  Temperature operating range ̶ Industrial (-40 °C to +85 °C) 2 SAM G53G / SAM G53N [DATASHEET] Atmel-11240F-ATARM-SAM-G53G-SAM-G53N-Datasheet_24-Jul-15 1. Configuration Summary Table 1-1 summarizes the SAM G53 device configurations. Table 1-1. Configuration Summary Feature SAM G53G19 Flash 512 Kbytes SRAM 96 Kbytes Package WLCSP49 Number of PIOs 38 Event System Yes 8 channels Performance: 800 KSps at 10-bit resolution 200 KSps at 11-bit resolution 12-bit ADC 50 KSps at 12-bit resolution 6 channels 16-bit Timer (3 external channels) I2SC/PDM 2 / 1-channel 2-way PDC Channels 28 USART/UART 1/2 SPI 1 2 masters at 400Kbits/s and TWI 1 slave at 3.4Mbit/s SAM G53N19 512 Kbytes 96 Kbytes LQFP100 38 Yes 8 channels Performance 800 KSps at 10-bit resolution 200 KSps at 11-bit resolution 50 KSps at 12-bit resolution 6 channels (3 external channels) 2 / 1-channel 2-way 28 1/2 1 2 masters 400Kbits/s and 1 slave 3.4Mbit/s SAM G53G / SAM G53N [DATASHEET] Atmel-11240F-ATARM-SAM-G53G-SAM-G53N-Datasheet_24-Jul-15 3 2. Block Diagram Figure 2-1. SAM G53 Block Diagram TDI TDO JTTTCMAKS//GSSSEWWLCDILOK VDDIO VDDOUT TST PCK[2:0] WKUP[15:0] XIN XOUT XIN32 XOUT32 ERASE VDDIO VDDCORE NRST PLL RC OSC 8/16/24 MHz Power Management Controller Power-on Reset 256-bit GPBR 3-20 MHz Crystal Osc. or External Osc. (bypass) Supply Controller Tamper Detection 32K Crystal Osc. or External Osc. (bypass) 32K RC Real-time Clock Real-time Timer Watchdog Timer Reset Controller Supply Monitor PIOA/PIOB System Controller JTAG and Serial Wire In-Circuit Emula.


SAMG53G SAMG53N SAMG53G19A


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)