DatasheetsPDF.com

FT201X Dataheets PDF



Part Number FT201X
Manufacturers FTDI
Logo FTDI
Description USB I2C SLAVE
Datasheet FT201X DatasheetFT201X Datasheet (PDF)

FT201X USB I2C SLAVE IC Datasheet Version 1.6 Document No.: FT_000627 Clearance No.: FTDI# 264 Future Technology Devices International Ltd. FT201X (USB I2C SLAVE IC) The FT201X is a USB to I2C interface with the following advanced features:  Single chip USB to I2C slave interface.  Up to 3.4MHz, high speed mode, I2C supported   Entire USB protocol handled on the chip. No USB specific firmware programming required.   Fully integrated 2048 byte multi-timeprogrammable (MTP) memory, s.

  FT201X   FT201X


Document
FT201X USB I2C SLAVE IC Datasheet Version 1.6 Document No.: FT_000627 Clearance No.: FTDI# 264 Future Technology Devices International Ltd. FT201X (USB I2C SLAVE IC) The FT201X is a USB to I2C interface with the following advanced features:  Single chip USB to I2C slave interface.  Up to 3.4MHz, high speed mode, I2C supported   Entire USB protocol handled on the chip. No USB specific firmware programming required.   Fully integrated 2048 byte multi-timeprogrammable (MTP) memory, storing device  descriptors and CBUS I/O configuration.  Fully integrated clock generation with no external crystal required plus optional clock  output selection enabling a glue-less interface to external MCU or FPGA.   512 byte receive buffer and 512 byte transmit  buffer utilising buffer smoothing technology to allow for high data throughput.   FTDI’s royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the  requirement for USB driver development in  most cases.  Configurable CBUS I/O pins.   Transmit and receive LED drive signals.   USB Battery Charger Detection. Allows for USB  peripheral devices to detect the presence of a higher power source to enable improved charging.   Device supplied pre-programmed with unique USB serial number. USB Power Configurations; supports buspowered, self-powered and bus-powered with power switching. Integrated +3.3V level converter for USB I/O. True 3.3V CMOS drive output and TTL input; Operates down to 1V8 with external pull-ups. Tolerant of 5V input. Configurable I/O pin output drive strength; 4 mA (min) and 16 mA (max). Integrated power-on-reset circuit. Fully integrated AVCC supply filtering - no external filtering required. + 5V Single Supply Operation. Internal 3V3/1V8 LDO regulators Low operating and USB suspend current; 8mA (active-typ) and 125uA (suspend-typ). UHCI/OHCI/EHCI host controller compatible. USB 2.0 Full Speed compatible. Extended operating temperature range; -40 to 85⁰C. Available in compact Pb-free 16 Pin SSOP and QFN packages (both RoHS compliant). Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminar y information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom. Scotland Registered Company Number: SC136640 Copyright © Future Technology Devices International Limited 1 1 Typical Applications  Upgrading Legacy Peripherals to USB  Utilising USB to add system modularity  Incorporate USB interface to enable PC transfers for development system communication  Motherboard and system monitoring through USB FT201X USB I2C SLAVE IC Datasheet Version 1.6 Document No.: FT_000627 Clearance No.: FTDI# 264  USB dongle implementations for Software/ Hardware Encryption and Wireless Modules  Interfacing MCU/PLD/FPGA based designs to add USB connectivity  USB Instrumentation  USB Industrial Control  USB Digital Camera Interface  Ability to detect dedicated charging ports for high current charging of batteries in portable devices 1.1 Driver Support Royalty free VIRTUAL COM PORT (VCP) DRIVERS for...  Windows 10 32-,64-bit  Windows 8 32,64-bit  Windows 7 32,64-bit  Windows Vista and Vista 64-bit  Windows XP and XP 64-bit  Windows Embedded Operating Systems  Server 2003, XP and Server 2008  Windows CE 4.2, 5.0 and 6.0  Mac OS-X  Linux 3.2 and greater  Android Royalty free D2XX Direct Drivers (USB Drivers + DLL S/W Interface)  Windows 10 32-,64-bit  Windows 8 32,64-bit  Windows 7 32,64-bit  Windows Vista and Vista 64-bit  Windows XP and XP 64-bit  Windows Embedded Operating Systems  Server 2003, XP and Server 2008  Windows CE 4.2, 5.0 and 6.0  Mac OS-X  Linux 2.6 and greater  Android The drivers listed above are all available to download for free from FTDI website (www.ftdichip.com). Various 3rd party drivers are also available for other operating systems - see FTDI website (www.ftdichip.com) for details. For.


FT220XS-x FT201X FT201XQ-x


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)