Document
C400 2.5-Inch NAND Flash SSD Features
C400 2.5-Inch SATA NAND Flash SSD
MTFDDAC128MAM, MTFDDAC256MAM, MTFDDAC512MAM MTFDDAK128MAM, MTFDDAK256MAM, MTFDDAK512MAM
Features
• Micron® 25nm MLC NAND Flash • RoHS-compliant package • SATA 6 Gb/s interface • ATA modes supported
– PIO mode 3, 4 – Multiword DMA mode 0, 1, 2 – Ultra DMA mode 0, 1, 2, 3, 4, 5 • Industry-standard, 512-byte sector size support • Hot-plug capable • Native command queuing support with 32-command slot support • ATA-8 ACS2 command set compliant • ATA security feature command set and password login support • Secure erase (data page) command set: fast and secure erase • Self-monitoring, analysis, and reporting technology (SMART) command set • Performance1, 2 – Sequential 128k READ: up to 500 MB/s – Sequential 128k WRITE: up to 260 MB/s – Random 4k READ: up to 45,000 IOPS – Random 4k WRITE: up to 50,000 IOPS – PCMark® Vantage (HDD test suite score): up to
75,000 – READ/WRITE latency: 55µs (TYP)
• Reliability – MTTF: 1.2 million device hours3 – Static and dynamic wear leveling – Uncorrectable bit error rate (UBER): <1 sector per 1015 bits read – Low power consumption – <280mW TYP4
• Endurance: Total bytes written (TBW) – 72TB • Capacity5 (unformatted): 128GB, 256GB, 512GB • Mechanical – 9.5mm height
– SATA connector: 5V ±10% – 2.5-inch drive: 100.5mm x 69.85mm x 9.5mm – Weight: 75g (MAX) • Mechanical – 7.0mm height – SATA connector: 5V ±10% – 2.5-inch drive: 100.5mm x 69.85mm x 7.0mm – Weight: 73g (MAX) • Field-updateable firmware • Operating temperature – Commercial (0°C to +70°C)6
Notes:
1. Typical I/O performance numbers as measured using Iometer with a queue depth of 32 and write cache enabled.
2. 4K transfers used for READ/WRITE latency values.
3. The product achieves a mean time to failure (MTTF) based on population statistics not relevant to individual units.
4. Active power measured during execution of MobileMark® 2007 with DIPM (device-initiated power management) enabled.
5. 1GB = 1 billion bytes; formatted capacity is less.
6. Drive case temperature.
Warranty: Contact your Micron sales representative for further information regarding the product, including product warranties.
PDF: 09005aef8455a0a5 c400_2_5_128-512gb.pdf - Rev. F 07/12 EN
1 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are subject to change by Micron without notice.
C400 2.5-Inch NAND Flash SSD Features
Part Numbering Information
Micron’s C400 SSD is available in different configurations and densities. Visit www.micron.com for a list of valid part numbers.
Figure 1: Part Number Chart
Micron Technology
Product Family FD = Flash drive
Drive Interface D = SATA 6.0 Gb/s
Drive Form Factor AC = 2.5-inch (9.5mm) AK = 2.5-inch (7mm)
Drive Density 128 = 128GB 256 = 256GB 512 = 512GB
NAND Flash Type M = MLC
Product Family AM = C400
MT FD D AC xxx M AM - 1 K x x xx
ES
Production Status Blank = Production ES = Engineering sample
Operating Temperature Range Blank = Commercial (0°C to +70°C)
Hardware Feature Set Blank = Null AA = Contact factory AB = Contact factory AC = Contact factory
Firmware Feature Set Blank = Null 1 = Contact factory 2 = Contact factory
BOM Revision For example: 1 = 1st generation 2 = 2nd generation
NAND Flash Component J = 32Gb, MLC, x8, 3.3V (25nm) K = 64Gb, MLC, x8, 3.3V (25nm)
Sector Size 1 = 512-byte
PDF: 09005aef8455a0a5 c400_2_5_128-512gb.pdf - Rev. F 07/12 EN
2 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved.
C400 2.5-Inch NAND Flash SSD General Description
General Description
Micron’s solid state drive (SSD) uses a single-chip controller with a SATA interface on the system side and n-channels of Micron NAND Flash internally. Packaged in an HDD replacement enclosure, the SSD integrates easily in existing storage infrastructures.
The SSD is designed to use the SATA interface efficiently during both READs and WRITEs while delivering bandwidth-focused performance. SSD technology enables enhanced boot times, faster application load times, reduced power consumption, and extended reliability.
Figure 2: Functional Block Diagram
SSD SATA controller
NAND NAND NAND
NAND NAND
DRAM buffer
PDF: 09005aef8455a0a5 c400_2_5_128-512gb.pdf - Rev. F 07/12 EN
3 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved.
C400 2.5-Inch NAND Flash SSD Logical Block Address Configuration
Logical Block Address Configuration
The drive is set to report the number of logical block addresses (LBA) that will ensure sufficient storage space for the specified density. Standard LBA settings, based on the IDEMA standard (LBA1-02), are shown below.
Table 1: Standard LBA Settings
Drive Size 128GB 256GB 512GB
Total LBA
Decimal
Hexadeci.