Document
Technical Document
LCD Specification
LCD Group
Product Specification September 2010
XGA module with True Industrial-rated LED backlight at 50,000 hours and built-in
backlight driver; high contrast of 800:1 and brightness of 350 nits.
3
RECORDS OF REVISION
LQ150X1LG93
SPEC No. LD-22902A
DATE
REVI
SED No PAGE
2010/9/15
SUMMARY -
NOTE
- Contents -
No. page
1 Application
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 1
2 Overview
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 2
3 Mechanical Specifications ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 2
4 Input Terminals
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 3
5 Absolute Maximum Ratings ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 9
6 Electrical Characteristics ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 10
7 Timing characteristics of input signals ・・・・・・・・・・・・・・・・・・・・・・ 12
8 Input Signals, Basic Display Colors and Gray Scale of Each Color ・・ 13
9 Optical Characteristics ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 15
10 Handling Precautions ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 17
11 Packing form
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 18
12 Reliability test items
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 18
13 Others
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 19
14 Storage conditions
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 20
Fig.1 OUTLINE DIMENSIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 21
Fig.3 PACKING FORM
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 22
1.Application
LD-22902A- 1
This specification applies to the color TFT-LCD module LQ150X1LG93.
This specification is the proprietary product of SHARP CORPORATION (SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP.
The device listed in this specification was designed and manufactured for use in general electronic equipment.
In case of using the device for applications such as control and safety equipment for transportation (controls of aircraft, trains, automobiles, etc.), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant system design should be taken.
Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications, telecommunication equipment (trunk lines), nuclear power control equipment and medical or other equipment for life support.
SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in this specification .
Contact and consult with a SHARP sales representative for any questions about this device.
2.Overview
LD-22902A- 2
This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a White-LED Backlight unit. Graphics and texts can be displayed on a 1024×RGB×768dots panel with about 16 million colors by using LVDS (Low Voltage Differential Signaling) and supplying +3.3V DC supply voltages for TFT-LCD panel driving and supply voltage for backlight.
The maximum viewing angle is in the 6o'clock direction. The 12o'clock direction is difficult to reverse the grayscale. The LED driver circuit and the PWM circuit to drive the backlight are built into the module.
3.Mechanical technical literatures
Parameter Display size Active area
Pixel format
Aspect ratio Pixel pitch Pixel configuration Display mode Unit outline dimensions
Mass Surface treatment
technical literatures 38(15inch)Diagonal 304.1(H)×228.1(V) 1024(H)×768(V) (1pixel=R+G+B dot)
4:3 0.297(H)×0.297(V) R,G,B vertical stripe
Normally white 326.5(W)×253.5(H)×9.6(D)
950 (Max.) Anti-glare and hard-coating 3H
Unit cm mm pixel
mm
mm g
Outline dimensions are shown in Fig.1.
LD-22902A- 3
4.Input Terminals
4-1.TFT-LCD panel driving CN1(Interface signals and +3.3V power supply) Using connectors:DF14H-20P-1.25H(56) (Hirose Electric Co., Ltd.) Corresponding connectors:DF14-20S-1.25C(conector) (Hirose Electric Co., Ltd.) :DF14-2628SCF(terminal) (Hirose Electric Co., Ltd.) Using LVDS receiver:Building into cotroll IC(THC63LVDF84B(Thine electronics) or Compatible product) Corresponding LVDS transmitter:THC63LVDM83R(Thine electronics) or Compatible product
CN1 Pin Symbol 1 VCC 2 VCC 3 GND 4 GND 5 RxIN06 RxIN0+ 7 GND 8 RxIN19 RxIN1+ 10 GND 11 RxIN212 RxIN2+ 13 GND 14 CK IN15 CK IN+ 16 GND 17 RxIN318 RxIN3+ 19 RL/UD 20 SELLVDS
Function +3.3V Power supply +3.3V Power supply
GND GND LVDS receiver signal CH0 (-) LVDS receiver signal CH0 (+) GND LVDS receiver signal CH1 (-) LVDS receiver signal CH1 (+) GND LVDS receiver signal CH2 (-) LVDS receiver signal CH2 (+) GND LVDS receiver signal CK (-) LVDS receiver signal CK (+) GND LVDS re.