Document
Approve Sheet Part Number: GBJ6A~GBJ6K
DATA SHEET GBJ6A~GBJ6K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE - 50 to 800 Volts CURRENT - 6.0 Amperes
GBJ
FEATURES
C 0.118 (3.0)
• Plastic material has Underwriters Laboratory Flammability Classification 94V-O • Ideal for printed circuit board • Reliable low cost construction utilizing molded plastic technique • Surge overload rating: 175 Amperes peak
Unit: inch ( mm )
0.996(25.3) 0.972(24.7)
0.122(3.1) 0.142(3.6)
0.189(4.8) 0.173(4.4) 0.150(3.8) 0.133(3.4)
0.146(3.7) 0.129(3.3)
• High temperature soldering guaranteed: 260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
0.578(14.7) 0.603(15.3)
MECHANICAL DATA
molded plastic technique Terminals: Leads solderable per MIL-STD-202, Method 208 Mounting position: Any Mounting torque: 5 in. lb. Max. Weight: 0.15 ounce, 4.0 grams
0.087(2.2) 0.070(1.8) 0.044(1.1) 0.035(0.9) 0.304(7.7) 0.288(7.3)
0.669(17.0) 0.709(18.0)
Case: Reliable low cost construction utilizing
0.115(2.9) 0.098(2.5)
0.304(7.7) 0.288(7.3)
0.304(7.7) 0.288(7.3)
0.032(0.8) 0.024(0.6)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%.
0.382(9.7) 0.366(9.3)
GBJ6A Maximum Recurrent Peak Reverse Voltage Maximum RMS Input Voltage Maximum DC Blocking Voltage Maximum Average Forward TC=100°C Rectified Output Current I2t Rating for fusing ( t<8.3ms) Peak Forward Surge Current single sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage Drop per element at 6.0A Maximum Reverse Leakage at rated TA=25° CDc Blocking Voltage per element TC=100°C Typical Thermal Resistance per leg(Note 2) RθJA Typical Thermal Resistance per leg(Note 3) RθJC Operating and Storage Temperature Range, TJ,TSTG 50 35 50
GBJ6B 100 70 100
GBJ6D 200 140 200
GBJ6G 400 280 400 6.0
GBJ6J 600 420 600
GBJ6K 800 560 800
UNIT V V V A A2sec
127 175 1.0 5 500 8.6 3.1 -55 to +150
Apk Vpk µA µA °C / W °C / W °C
NOTES: 1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw. 2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads. 3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
PAGE . 1
Approve Sheet Part Number: GBJ6A~GBJ6K
RATING AND CHARACTERISTIC CURVES
INSTANTANEOUS FORWARD CURRENT, AMPERES
100 40 20 10 4.0 2.0 1.0 TJ=25OC Pulse Width=300 S 1% DULY Cycle
6.0
AVERAGE FORWARD CURRENT AMPERES
4.0
HEAT-SINK MOUNTING,TC (4* 4* 0.15) INCH COPPER PLATE
2.0 MOUNTED ON PC BOARD. TA 0.5"(12.7mm) LEAD LENGTH 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 50 100 150
0.4 0.2 0.1 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4
TEMPERATURE OC
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
Fig. 1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT
Fig. 2- TYPICAL INSTANTANEOUS FORWARD CHARACTERISI.