Document
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LG Radial Lead Type, Higher Capacitance series
Higher Capacitance, Low ESR, High ripple current. Load life of 2000 hours at 105°C. Radial lead type : Lead free flow soldering condition correspondence Compliant to the RoHS directive (2002/95/EC).
LG
Higher Capacitance
Specifications
LF
Item
Performance Characteristics
Category Temperature Range – 55 to +105°C
Rated Voltage Range
2.5 to 16V
Rated Capacitance Range 330 to 3900µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics (Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25 Z– 55°C / Z+20°C 1.25
(100kHz)
Endurance
The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C.
Capacitance change tan δ ESR ( 1) Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value
Damp Heat (Steady State)
The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH.
Capacitance change tan δ ESR ( 1) Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value
Resistance to Soldering Heat
After soldering the capacitor under the soldering conditions prescribed here as preheat at 150 to 200°C for 60 to 180 seconds and peak temperature at 265°C for 10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side.
Capacitance change tan δ ESR ( 1) Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Resin coated Case Voltage(g:4V)
Silvered lead Wire
LG 1200 g 841 φD+0.5 MAX. P±0.5
Series
Lot. No.
L+0.5MAX.
φd 15MIN
4MIN
(mm)
Size φ8 × 9L φ8 × 12L φ10 × 13L
φD 8.0
8.0 10.0
L 8.5 11.5 12.5
P 3.5 3.5 5.0
φd 0.6 0.6 0.6
Voltage
V Code
2.5 e
Please refer to page 20 about the end seal configulation.
4 g
6.3 10 jA
16 C
Type numbering system (Example : 4V 1200µF)
1 2 3 4 5 6 7 8 9 10 11 12
P LG 0G 1 2 2 MCO 1
Size code Configuration Capacitance toleranc (±20%) Rated capacitance (1200µF) Rated voltage (4V) Series name
Type
Dimension table in next page.
CAT.8100Z
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LG series
Standard Ratings
Rated Voltage (V) Code
Surge Voltage (V)
Rated Capacitance (µF)
2.5 (0E)
2.8
4 (0G)
4.6
6.3 (0J)
7.2
10 (1A)
16 (1C)
11.5 18.4
1800 2200 2700 3900 1200 1800 2700
820 1200 1500 1800
560 820 1200 330 470 820
Case Size φD × L (mm)
8×9 8 × 12 10 × 13 10 × 13 8×9 8 × 12 10 × 13 8×9 8 × 12 10 × 13 10 × 13 8×9 8 × 12 10 × 13 8×9 8 × 12 10 × 13
tan δ
0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08
Leakage Current ESR (mΩ)
Rated Ripple
(µA)
(at 100kHz 20°C)
(mArms)
Part Number
900
9
6000
PLG0E182MCO1
1100
8
6700
PLG0E222MDO1
1350
8
5560
PLG0E272MDO1
1950
8
7000
PLG0E392MDO1
960
9
5900
PLG0G122MCO1
1440
9
6500
PLG0G182MDO1
2160
8
6900
PLG0G272MDO1
1033
9
5700
PLG0J821MCO1
1512
9
6100
PLG0J122MDO1
1890
9
6300
PLG0J152MDO1
2268
8
6600
PLG0J182MDO1
1120
11
5100
PLG1A561MCO1
1640
10
5800
PLG1A821MDO1
2400
9
6200
PLG1A122MDO1
1056
13
4700
PLG1C331MCO1
1504
11
5400
PLG1C471MDO1
2624
11
5600
PLG1C821MDO1
Rated ripple current (mArms) at 105°C 100kHz
Taping specifications are given in page 20, 21, 22. Please refer to page 3 for the minimum order quantity.
CAT.8100Z
.