DatasheetsPDF.com

PSN30-15AO Dataheets PDF



Part Number PSN30-15AO
Manufacturers Autonics
Logo Autonics
Description INDUCTIVE PROXIMITY SENSOR
Datasheet PSN30-15AO DatasheetPSN30-15AO Datasheet (PDF)

▣ Specifications INDUCTIVE PROXIMITY SENSOR(SQUARE AC 2WIRE) ▣ Mutual-interference & Influence by surrounding metals ◎Mutual-interference PSN30-10AO PSN30-10AC 10㎜ PSN30-15AO PSN30-15AC 15㎜ PSN40-20AO PSN40-20AC 20㎜ When several proximity sensors are mounted closely, malfunction of sensor may be caused due to mutual interference. Therefore, be sure to keep a minimum distance between the two sensors as below chart. Face to Face Parallel A B PSN SERIES M A N U A L Model PSN25-5AO PSN25-5AC 5㎜ .

  PSN30-15AO   PSN30-15AO


Document
▣ Specifications INDUCTIVE PROXIMITY SENSOR(SQUARE AC 2WIRE) ▣ Mutual-interference & Influence by surrounding metals ◎Mutual-interference PSN30-10AO PSN30-10AC 10㎜ PSN30-15AO PSN30-15AC 15㎜ PSN40-20AO PSN40-20AC 20㎜ When several proximity sensors are mounted closely, malfunction of sensor may be caused due to mutual interference. Therefore, be sure to keep a minimum distance between the two sensors as below chart. Face to Face Parallel A B PSN SERIES M A N U A L Model PSN25-5AO PSN25-5AC 5㎜ Sensing distance Hysteresis Standard sensing target Setting distance Power supply (Operating voltage) Lackage current Response frequency Residual voltage Effect by Temp. Max. 10% of sensing distance 25×25×1㎜(Iron) 0 to 3.5㎜ 30×30×1㎜(Iron) 0 to 7㎜ 45×45×1㎜(Iron) 0 to 10.5㎜ 60×60×1㎜(Iron) 0 to 14㎜ m 100-240VAC 50/60Hz (85-264VAC) Max. 2.5mA 20㎐ Max. 10V Within ±10℃ max. of sensing distance at 20℃ in temperature range of -25 to 70℃ 5 to 200mA Min. 50㏁(at 500VDC megger) 1,500VAC 50/60㎐ for 1minute 1㎜ amplitude at frequency of 10 to 55㎐ in each of X, Y, Z directions for 2 hours 500㎨(50G) in X, Y, Z directions for 3 times Operating indicator(Red LED) -25 to 70℃, Storage: -30 to 80℃ 35 to 95%RH, Storage: 35 to 95%RH Surge protection IP67(IEC standards) Case: Heat-resistant ABS, Standard cable(Black): Polyvinyl chloride(PVC). Moving direction Target Item C ℓ d m ◎Influence by surrounding metals When sensors are mounted on metallic panel, it is required to protect the sensors from malfunction by any metallic object. Therefore, be sure to keep a minimum distance as below chart. (Unit:mm) Model Thank you very much for selecting Autonics products. For your safety, please read the following before using. Control output Insulation resistance Dielectric strength Vibration Shock Indicator Environment Ambient temperature Ambient humidity PSN30 PSN25 10㎜ 15㎜ 90 65 5 45 45 35 120 70 5 60 45 35 30 40 5 15 25 20 60 50 5 30 30 25 PSN40 ▣ Caution for your safety ※Please keep these instructions and review them before using this unit. ※Please observe the cautions that follow; A B C d ℓ m Warning Serious injury may result if instructions are not followed. Caution Product may be damaged, or injury may result if instructions are not followed. ※The following is an explanation of the symbols used in the operation manual. Caution:Injury or danger may occur under special conditions. Warning 1. In case of using this unit with machineries(Nuclear power control, medical equipment vehicle, train, airplane, combustion apparatus, entertainment or safety device etc), it is required to install fail-safe device, or contact us for information required. It may cause a fire, human injury or property loss. Protection circuit Protection Materials Approval Unit Weight Approx. 65g ▣ Setting distance Target ● Sensing distance can be changed by the shape, size or material of the target. Therefore please check the sensing distance like (a), then pass the target within range of setting distance(Sa) like (b). Setting distance(Sa) = Sensing distance(Sn) × 70% Ex)PSN30-10AO Setting distance(Sa) = 10mm × 0.7 = 7mm Caution 1. Do not use this unit in place where flammable, explosive gas, chemical strong alkalis, or acids exist. It may cause a fire or explosion. 2. Do not impact on this unit. It may cause malfunction or damage to the product. 3. Do not use this unit beyond rated power. It may result in serious damage to the product. Approx. 106g Approx. 152g Moving direction Sa Sn ● ※ Environment resistance is rated at no freezing or condensation. { Sa:Setting distance Sn:Sensing distance (70% of Sn) ▣ Dimensions PSN25 / PSN30 / PSN40 A B C (Unit:mm) (a) (b) PSN25 25 35.5 ø4.2 18 25.3 16.8 39 4 PSN30 30 48.5 ø4.5 22 30 20 53 4 PSN40 40 47 ø5.5 30 40 25 53 4 ▣ Ordering information P SN 25 5 AC Control output ▣ Caution for using 1. This equipment shall not be used outdoors or beyond specified temperature range. 2. Do not apply over tensile strength of cord. (ø4: max. 30N) 3. Do not use the same conduit with cord of this unit and electric power line or power line. 4. Tighten strength of installing screws should be under 10kgf.cm. 5. Please check the voltage changes of power source in order not to excess the rated power input. 6. Do not connect directly output terminal to capacitive load. 7. Please make wire as short as possible in order to avoid noise. 8. Be sure to use cable as indicated specification on this product. If wrong cable or bended cable is used, it shall not maintain the water-proof. 9. It is possible to extend cable with over 0.3mm2 and max. 200m. 10. If the target is plated, the operating distance can be changed by the plating material. 11. It may cause malfunction by metal particle on product. 12. If there are machines(motor, welding, etc.), which occurs big surge around this unit, please install the varistor or absorber to source of surge, even though there is built-in surge absorber in this unit. 13. If connecting the load wi.


PSN30-10AC PSN30-15AO PSN30-15AC


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)