DatasheetsPDF.com

PM200CVA060 Dataheets PDF



Part Number PM200CVA060
Manufacturers Mitsubishi
Logo Mitsubishi
Description INTELLIGENT POWER MODULES
Datasheet PM200CVA060 DatasheetPM200CVA060 Datasheet (PDF)

MITSUBISHI MITSUBISHI MODULES> PM200CVA060 PM200CVA060 FLAT-BASE FLAT-BASE TYPE TYPE INSULATED INSULATED PACKAGE PACKAGE PM200CVA060 FEATURE • 3φ 200A, 600V Current-sense IGBT for 20kHz switching • Monolithic gate drive & protection logic • Detection, protection & status indication circuits for overcurrent, short-circuit, over-temperature & under-voltage (P-FO available from upper leg devices) • Acoustic noise-less 22kW class inverter application .

  PM200CVA060   PM200CVA060



Document
MITSUBISHI MITSUBISHI MODULES> PM200CVA060 PM200CVA060 FLAT-BASE FLAT-BASE TYPE TYPE INSULATED INSULATED PACKAGE PACKAGE PM200CVA060 FEATURE • 3φ 200A, 600V Current-sense IGBT for 20kHz switching • Monolithic gate drive & protection logic • Detection, protection & status indication circuits for overcurrent, short-circuit, over-temperature & under-voltage (P-FO available from upper leg devices) • Acoustic noise-less 22kW class inverter application • UL Recognized Yellow Card No. E80276(N) File No. E80271 APPLICATION General purpose inverter, servo drives and other motor controls PACKAGE OUTLINES Dimensions in mm 7.5 7.5 15.1 120 105 ±0.25 12.3 4–φ5.5MOUNTING HOLES 1 234 102 89.2 ±0.5 87 ±0.25 9 10 1112 13 141516 17 18 19 U V W 12.3 2.54 ±0.25 5-M5NUTS 12 43.57 ±0.3 5678 14.1 ±0.25 14.1 ±0.25 14.1 ±0.25 TERMINAL CODE 1. WFO 8. VVP1 15. VNC 2. VWPC 9. UFO 16. VN1 3. WP 10. VUPC 17. UN 4. VWP1 11. UP 18. VN 5. VFO 12. VUP1 19. WN 6. VVPC 13. NC 14. FO 7. VP 1.1 ±0.3 18.25 85.2 19.5 22 22 12 24.1 –0.5 21.6 4 24.1 33.7 34.7 +1.0 LABEL P N 14.6 ±0.3 A 2.54 ±0.25 2.54 ±0.25 2.54 ±0.25 3.49 ±0.25 3.49 ±0.25 4-φ3 C0.7 0.64 A : DETAIL Jun. 2005 MITSUBISHI PM200CVA060 FLAT-BASE TYPE INSULATED PACKAGE INTERNAL FUNCTIONS BLOCK DIAGRAM FO Rfo Rfo Rfo Rfo NC VNC WN VN1 VN UN WP VWP1 VP VVP1 UP VUP1 VWPC WFO VVPC VFO VUPC UFO GND FO In VCC TEMP GND Si OUT Th GND FO In VCC GND In FO VCC GND FO In VCC GND FO In VCC GND FO In VCC GND Si OUT GND Si OUT GND Si OUT GND Si OUT GND Si OUT Rfo=1.5kΩ N W V U P MAXIMUM RATINGS (Tj = 25°C, unless otherwise noted) INVERTER PART Symbol VCES ±IC ±ICP PC Tj Parameter Collector-Emitter Voltage Collector Current Collector Current (Peak) Collector Dissipation Junction Temperature Condition VD = 15V, VCIN = 15V TC = 25°C TC = 25°C TC = 25°C Ratings 600 200 400 541 –20 ~ +150 Unit V A A W °C CONTROL PART Symbol VD VCIN VFO IFO Parameter Supply Voltage Input Voltage Fault Output Supply Voltage Fault Output Current Condition Applied between : VUP1-VUPC VVP1-VVPC, VWP1-VWPC, VN1-VNC Applied between : UP-VUPC, VP-VVPC, WP-VWPC UN • VN • WN-VNC Applied between : UFO-VUPC, VFO-VVPC, WFO-VWPC FO-VNC Sink current at UFO, VFO, WFO and FO terminal Ratings 20 20 20 20 Unit V V V mA Jun. 2005 MITSUBISHI PM200CVA060 FLAT-BASE TYPE INSULATED PACKAGE TOTAL SYSTEM Parameter Supply Voltage Protected by VCC(PROT) SC Symbol VCC(surge) Supply Voltage (Surge) TC Tstg Viso Module Case Operating Temperature Storage Temperature Isolation Voltage Condition VD = 13.5 ~ 16.5V, Inverter Part, Tj = 125°C Start Applied between : P-N, Surge value or without switching (Note-1) 60Hz, Sinusoidal, Charged part to Base, AC 1 min. Ratings 400 500 –20 ~ +100 –40 ~ +125 2500 Unit V V °C °C Vrms (Note-1) TC measurement point is below. (3mm depth at the center of the side of base plate) Tc ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise noted) INVERTER PART Symbol VCE(sat) VEC ton trr tc(on) toff tc(off) ICES Parameter Collector-Emitter Saturation Voltage FWDi Forward Voltage Test Condition VD = 15V, IC = 200A VCIN = 0V –IC = 200A, VD = 15V, VCIN = 15V VD = 15V, VCIN = 0V↔15V VCC = 300V, IC = 200A Tj = 125°C Inductive Load (upper and lower arm) VCE = VCES, VCIN = 15V Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C Min. — — — 0.4 — — — — — — Limits Typ. 2.35 2.55 2.20 0.8 0.2 0.3 1.8 0.6 — — Max. 2.80 3.05 3.30 2.1 0.3 1.1 2.9 1.2 1 10 Unit V V Switching Time µs Collector-Emitter Cutoff Current mA CONTROL PART Symbol ID Vth(ON) Vth(OFF) SC toff(SC) OT OTr UV UVr IFO(H) IFO(L) tFO Parameter Circuit Current Input ON Threshold Voltage Input OFF Threshold Voltage Short Circuit Trip Level Short Circuit Current Delay Time Over Temperature Protection Supply Circuit Under-Voltage Protection Fault Output Current Minimum Fault Output Pulse Width Test Condition VD = 15V, VCIN = 15V VN1-VNC V*P1-V*PC Min. — — 1.2 1.7 310 — Trip level Reset level Trip level Reset level (Note-2) (Note-2) 111 — 11.5 — — — 1.0 Limits Typ. 40 13 1.5 2.0 — 10 118 100 12.0 12.5 — 10 1.8 Max. 55 18 1.8 2.3 — — 125 — 12.5 — 0.01 15 — Unit mA V A µs °C V mA ms Applied between : UP-VUPC, VP-VVPC, WP-VWPC UN • VN • WN-VNC –20≤ Tj ≤ 125°C, VD = 15V VD = 15V Base-plate Temperature detection, VD = 15V –20≤ Tj ≤ 125°C VD = 15V, VFO = 15V VD = 15V (Note-2) Fault output is given only when the internal SC, OT & UV protection. Fault output of OT protection operate by lower arm Fault output of OT, UV protection given pulse while over level. Jun. 2005 MITSUBISHI PM200CVA060 FLAT-BASE TYPE INSULATED PACKAGE THERMAL RESISTANCES Symbol Rth(j-c)Q Rth(j-c)F Rth(c-f) Parameter Junction to case Thermal Resistances Contact Thermal Resistance Test Condition Inverter IGBT part (per 1/6 module) Inverter FWDi part (per 1/6 module) Case to fin, Thermal grease applied (per 1 module) Min. — — — L.


PM200CVA060 PM200CVA060 PM200CSE060


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)