DatasheetsPDF.com

KSZ9031RNX Dataheets PDF



Part Number KSZ9031RNX
Manufacturers Micrel Semiconductor
Logo Micrel Semiconductor
Description Gigabit Ethernet Transceiver
Datasheet KSZ9031RNX DatasheetKSZ9031RNX Datasheet (PDF)

KSZ9031RNX Gigabit Ethernet Transceiver with RGMII Support Data Sheet Rev. 1.0 General Description The KSZ9031RNX is a completely integrated triple-speed (10Base-T/100Base-TX/1000Base-T) Ethernet physicallayer transceiver for transmission and reception of data on standard CAT-5 unshielded twisted pair (UTP) cable. The KSZ9031RNX provides the Reduced Gigabit Media Independent Interface (RGMII) for direct connection to RGMII MACs in Gigabit Ethernet processors and switches for data transfer at 10.

  KSZ9031RNX   KSZ9031RNX



Document
KSZ9031RNX Gigabit Ethernet Transceiver with RGMII Support Data Sheet Rev. 1.0 General Description The KSZ9031RNX is a completely integrated triple-speed (10Base-T/100Base-TX/1000Base-T) Ethernet physicallayer transceiver for transmission and reception of data on standard CAT-5 unshielded twisted pair (UTP) cable. The KSZ9031RNX provides the Reduced Gigabit Media Independent Interface (RGMII) for direct connection to RGMII MACs in Gigabit Ethernet processors and switches for data transfer at 10/100/1000Mbps. The KSZ9031RNX reduces board cost and simplifies board layout by using on-chip termination resistors for the four differential pairs and by integrating an LDO controller to drive a low-cost MOSFET to supply the 1.2V core. The KSZ9031RNX offers diagnostic features to facilitate system bring-up and debugging in production testing and in product deployment. Parametric NAND tree support enables fault detection between KSZ9031 I/Os and the ® board. The LinkMD TDR-based cable diagnostic identifies faulty copper cabling. Remote and local loopback functions verify analog and digital data paths. The KSZ9031RNX is available in a 48-pin, lead-free QFN package (see “Ordering Information”). Data sheets and support documentation are available on Micrel’s web site at: www.micrel.com. Features • Single-chip 10/100/1000Mbps IEEE 802.3 compliant Ethernet transceiver • RGMII timing supports on-chip delay according to RGMII Version 2.0, with programming options for external delay and making adjustments and corrections to TX and RX timing paths • RGMII with 3.3V/2.5V/1.8V tolerant I/Os • Auto-negotiation to automatically select the highest linkup speed (10/100/1000Mbps) and duplex (half/full) • On-chip termination resistors for the differential pairs • On-chip LDO controller to support single 3.3V supply operation – requires only one external FET to generate 1.2V for the core • Jumbo frame support up to 16KB • 125MHz reference clock output • Energy detect power-down mode for reduced power consumption when the cable is not attached • Energy Efficient Ethernet (EEE) support with low-power idle (LPI) mode and clock stoppage for 100Base-TX/ 1000Base-T and transmit amplitude reduction with 10Base-Te option • Wake-on-LAN (WOL) support with robust custom-packet detection Functional Diagram LinkMD is a registered trademark of Micrel, Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com October 2012 M9999-103112-1.0 Micrel, Inc. KSZ9031RNX Features (Continued) • Programmable LED outputs for link, activity, and speed • Baseline wander correction • LinkMD TDR-based cable diagnostic to identify faulty copper cabling • Parametric NAND tree support to detect faults between chip I/Os and board • Loopback modes for diagnostics • Automatic MDI/MDI-X crossover to detect and correct pair swap at all speeds of operation • Automatic detection and correction of pair swaps, pair skew, and pair polarity • MDC/MDIO management interface for PHY register configuration • Interrupt pin option • Power-down and power-saving modes • Operating voltages – Core (DVDDL, AVDDL, AVDDL_PLL): 1.2V (external FET or regulator) – VDD I/O (DVDDH): 3.3V, 2.5V, or 1.8V – Transceiver (AVDDH): 3.3V or 2.5V (commercial temp) • Available in a 48-pin QFN (7mm x 7mm) package Applications • • • • • • • • • • • Laser/Network printer Network attached storage (NAS) Network server Gigabit LAN on motherboard (GLOM) Broadband gateway Gigabit SOHO/SMB router IPTV IP set-top box Game console Triple-play (data, voice, video) media center Media converter Ordering Information Part Number KSZ9031RNXCA KSZ9031RNXCC KSZ9031RNXIA (1) Temperature Range 0°C to 70°C 0°C to 70°C −40°C to 85°C −40°C to 85°C Package 48-Pin QFN 48-Pin QFN 48-Pin QFN 48-Pin QFN Lead Finish Pb-Free Pb-Free Pb-Free Pb-Free Wire Bonding Gold Copper Gold Copper Description RGMII, Commercial Temperature, Gold Wire Bonding RGMII, Commercial Temperature, Copper Wire Bonding RGMII, Industrial Temperature, Gold Wire Bonding RGMII, Industrial Temperature, Copper Wire Bonding KSZ9031RNX Evaluation Board (Mounted with KSZ9031RNX device in commercial temperature) (1) KSZ9031RNXIC (1) KSZ9031RNX-EVAL Note: 1. 0°C to 70°C 48-Pin QFN Pb-Free Contact factory for lead time. October 2012 2 M9999-103112-1.0 Micrel, Inc. KSZ9031RNX Revision History Revision 1.0 Date 10/31/12 Summary of Changes Data sheet created October 2012 3 M9999-103112-1.0 Micrel, Inc. KSZ9031RNX Contents General Description ................................................................................................................................................................ 1 Features .................................................................................................................................................................................. 1 Functional Diagram ..........................................................


IFSC-1515AH-01 KSZ9031RNX MIC2033


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)