DatasheetsPDF.com

AUIPS6031 Dataheets PDF



Part Number AUIPS6031
Manufacturers International Rectifier
Logo International Rectifier
Description INTELLIGENT POWER HIGH SIDE SWITCH
Datasheet AUIPS6031 DatasheetAUIPS6031 Datasheet (PDF)

September, 12th 2011 Automotive grade AUIPS6031(S)(R) Done please find INTELLIGENT POWER HIGH SIDE SWITCH Features           Over temperature shutdown (with auto-restart) Short circuit protection (current limit) Reverse battery protection (turns On the MOSFET) Full diagnostic capability (short circuit to battery) Active clamp Open load detection in On and Off state Ground loss protection Logic ground isolated from power ground ESD protection Lead Free and RoHS compliant Product Sum.

  AUIPS6031   AUIPS6031


Document
September, 12th 2011 Automotive grade AUIPS6031(S)(R) Done please find INTELLIGENT POWER HIGH SIDE SWITCH Features           Over temperature shutdown (with auto-restart) Short circuit protection (current limit) Reverse battery protection (turns On the MOSFET) Full diagnostic capability (short circuit to battery) Active clamp Open load detection in On and Off state Ground loss protection Logic ground isolated from power ground ESD protection Lead Free and RoHS compliant Product Summary Rds(on) Vclamp I Limit Open load Packages 60m max. 39V 16A 3V / 0.55A Description The AUIPS6031(S)(R) is a five terminal Intelligent Power Switch (IPS) for use in a high side configuration. It features short circuit, over-temperature, ESD protection, inductive load capability and diagnostic feedback. The output current is limited to the Ilim value. The current limitation is activated until the thermal protection acts. The over-temperature protection turns off the device if the junction temperature exceeds the Tshutdown value. It will automatically restart after the junction has cooled 7°C below the Tshutdown value. The reverse battery protection turns On the MOSFET. A diagnostic pin provides different voltage levels for each fault condition. The double level shifter circuitry will allow large offsets between the logic and load ground. TO-220 AUIPS6031 D²Pak AUIPS6031S D-Pak AUIPS6031R Typical Connection +5V +Bat Vcc(3) Dg(4) Control Rdgs In(2) V Diag Rin Input Signal Load Gnd(1) Out(5) Pull-up resistors required for open load off and short circuit to Vbat detection Rdgp www.irf.com 1 Free Datasheet http://www.Datasheet4U.com AUIPS6031(S)(R) Qualification Information† Qualification Level Automotive †† (per AEC-Q100 ) Comments: This family of ICs has passed an Automotive qualification. IR’s Industrial and Consumer qualification level is granted by extension of the higher Automotive level. MSL1, 260°C D2PAK-5L (per IPC/JEDEC J-STD-020) TO-220 DPAK-5L Machine Model Human Body Model ESD Charged Device Model (DPAK,D2PAK) Charged Device Model (TO220) Not applicable (non-surface mount package style) MSL1, 260°C (per IPC/JEDEC J-STD-020) Class M2 (+/-150V) (per AEC-Q100-003) ††† Class H1C (+/-1500V) (per AEC-Q100-002) ††† Class C4 (+/-900V) (per AEC-Q100-011) ††† Class C3B (+/-750V) (per AEC-Q100-011) Class II, Level A (per AEC-Q100-004) Yes ††† Moisture Sensitivity Level IC Latch-Up Test RoHS Compliant † †† ††† Qualification standards can be found at International Rectifier’s web site http://www.irf.com/ Exceptions to AEC-Q100 requirements are noted in the qualification report. Passing voltage level www.irf.com 2 Free Datasheet http://www.Datasheet4U.com AUIPS6031(S)(R) Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are referenced to Ground lead. Tj= -40°C..150°C, Vcc=6..35V (unless otherwise specified). Symbol Vout Voffset Vin Vcc max. Vcc cont. Vcc sc. Iin max. Idg max. Vdg Pd Tj max. Parameter Maximum output voltage Maximum logic ground to load ground offset Maximum input voltage Maximum Vcc voltage Maximum continuous Vcc voltage Maximum Vcc voltage with short circuit protection Maximum IN current Maximum diagnostic output current Maximum diagnostic output voltage Maximum power dissipation (internally limited by thermal protection) Rth=5°C/W AUIPS6031 Rth=40°C/W AUIPS6031S 1”sqrt. footprint Rth=50°C/W AUIPS6031R 1”sqrt. footprint Max. storage & operating temperature junction temperature Min. Max. Units Vcc-35 Vcc+0.3 Vcc-35 Vcc+0.3 -0.3 5.5  36  28  30 -3 10 -3 10 -0.3 5.5    V mA V W °C -40 25 3.1 2.5 150 Thermal Characteristics Symbol Rth1 Rth2 Rth1 Rth2 Rth3 Rth1 Rth2 Rth3 Parameter Thermal resistance junction to ambient AUIPS6031 TO220 free air Thermal resistance junction to case AUIPS6031 TO220 Thermal resistance junction to ambient AUIPS6031S D²Pak std. footprint Thermal resistance junction to ambient AUIPS6031S D²Pak 1” sqrt. footprint Thermal resistance junction to case AUIPS6031S D²Pak Thermal resistance junction to ambient AUIPS6031R D-Pak std. footprint Thermal resistance junction to ambient AUIPS6031R D-Pak 1” sqrt. footprint Thermal resistance junction to case AUIPS6031R D-Pak Typ. 50 3.8 60 40 3.8 70 50 3.8 Max.         Units °C/W Recommended Operating Conditions These values are given for a quick design. For operation outside these conditions, please consult the application notes. Symbol VIH VIL Iout Parameter High level input voltage Low level input voltage Continuous drain current, Tambient=85°C, Tj=125°C, Vin=5V Rth=5°C/W AUIPS6031 Rth=40°C/W AUIPS6031S 1” sqrt. footprint Rth=50°C/W AUIPS6031R 1” sqrt. footprint Recommended resistor in series with IN pin Recommended resistor in series with DG pin for reverse battery protection Recommended pull-up resistor for DG Recommended pull-up resistor for open load detection Max. switching frequency Min. 4 0  .


IPS1011RPBF AUIPS6031 AUIPS6031S


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)