DatasheetsPDF.com

G084SN05-V1 Dataheets PDF



Part Number G084SN05-V1
Manufacturers AUO
Logo AUO
Description LCD
Datasheet G084SN05-V1 DatasheetG084SN05-V1 Datasheet (PDF)

www.DataSheet4U.net www.speclcd.com Spec. No.: Version: Total pages: Date: MDGD084-SN05-2 0.2 27 2004-August-30 AU OPTRONICS CORPORATION Product Functional Specifications 8.4 ” SVGA Color TFT-LCD Module with Touch Panel Model Name: G084SN05 V.1 Approved by Prepared by Martin Sun Cynthia Lin GD- MDBU Marketing Division / AU Optronics Croporation Customer Checked & Approved by (C) Copyright AU Optroncis, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G084SN05.

  G084SN05-V1   G084SN05-V1


Document
www.DataSheet4U.net www.speclcd.com Spec. No.: Version: Total pages: Date: MDGD084-SN05-2 0.2 27 2004-August-30 AU OPTRONICS CORPORATION Product Functional Specifications 8.4 ” SVGA Color TFT-LCD Module with Touch Panel Model Name: G084SN05 V.1 Approved by Prepared by Martin Sun Cynthia Lin GD- MDBU Marketing Division / AU Optronics Croporation Customer Checked & Approved by (C) Copyright AU Optroncis, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G084SN05 V.1 ver.0.2 1/1 www.speclcd.com www.DataSheet4U.net www.speclcd.com Version: 0.2 Total Pages: 27 Date: 2004/08/30 Product Functional Specification 8.4 inch SVGA Color TFT LCD Module with Touch Panel Model Name: G084SN05 V.1 (u ) Preliminary Specification ( ) Final Specification Note: This Specification is subject to change without notice. (C) Copyright AU Optroncis, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G084SN05 V.1 ver.0.2 2/2 www.speclcd.com www.DataSheet4U.net www.speclcd.com I. Contents 1.0 2.0 Handling Precautions…………………………………………………..…5 General Description……………………………………………………….6 2.1 Display Characteristics 2.2 Functional Block Diagram Absolute Maximum Ratings……………………………………………...8 Optical Characteristics……………………………………………………9 Signal Interface……………………………………………………………11 5.1 5.2 5.3 Connectors Signal Pin Signal Description 3.0 4.0 5.0 6.0 7.0 8.0 5.4 Signal Electrical Characteristics 5.5 Signal for Lamp Connector Pixel Format Image………………………………………………………15 Parameter Guide Line CFL Inverter…………………………………...16 Interface Timing..…………………………………………………………17 8.1 Timing Characteristics 8.2 Timing Definition 8.3 Timing Chart Power Consumption ……………………………………………………..20 Power ON/OFF Sequence……………………………………………….21 Touch Panel Specification ………………………………………………22 11.1 11.2 11.3 Operating Condition Electrical Characteristic Mechanical Characteristic 9.0 10.0 11.0 12.0 13.0 14.0 11.4 Optical Characteristic Reliability Test Items…………………………………………………..…24 Packing Dimension………………………………………………………25 Mechanical Characteristic..……………………………………………..26 (C) Copyright AU Optroncis, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G084SN05 V.1 ver.0.2 3/3 www.speclcd.com www.DataSheet4U.net www.speclcd.com II. Record of Revision Version and Date 0.1 2004/07/05 0.2 2004/08/12 Page All 6, 9 Old Description First Draft Contrast Ratio 350:1 typ., 250 min. 8 8 CCFL Current Min. 5mA CCFL Ignition Voltage: 500 Vrms 24, 25 All Contrast Ratio 500:1 typ., 400 min. 4mA CCFL Ignition Voltage: 670(25°C), 870 (0°C) Vrms Updated drawing (cable length) New Description Remark (C) Copyright AU Optroncis, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G084SN05 V.1 ver.0.2 4/4 www.speclcd.com www.DataSheet4U.net www.speclcd.com 1.0 Handing Precautions 1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnection from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) In case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT module may be damaged. 10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the interface Connector of the TFT module. 11) After installation of the TFT module into an enclosure, do not twist nor bend the TFT module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may be damaged. 12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or regulations for disposal. 13) Small amount of materials having no flammability grade is used in the LCD module should be supplied by power complied with requirements of Limited Power Source, or be applied exemption. 14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit. Do not connect the CFL in Hazardous Voltage Circuit. (C) Copyright AU Optroncis, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G084SN05 V.1 ver.0.2 5/5 www.speclcd.com www.DataSheet4U.net www.speclcd.com 2.0 General Description This specification applies to the 8.4 inch color TFT.


G084SN05-V0 G084SN05-V1 T370HW01V1


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)