DatasheetsPDF.com

G084SN05-V0 Dataheets PDF



Part Number G084SN05-V0
Manufacturers AUO
Logo AUO
Description LCD
Datasheet G084SN05-V0 DatasheetG084SN05-V0 Datasheet (PDF)

www.DataSheet4U.net Spec. No.: Version: Total pages: Date: MDGD084-SN05-0 0.2 23 2004- March-15 AU OPTRONICS CORPORATION Product Functional Specifications 8.4 ” SVGA Color TFT-LCD Module Model Name: G084SN05 V.0 Approved by Prepared by Martin Sun Cynthia Lin GD- MDBU Marketing Division / AU Optronics Croporation Customer Checked & Approved by (C) Copyright AU Optroncis, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G084SN05 V.0 ver.0.2 1/23 w w w . .

  G084SN05-V0   G084SN05-V0


Document
www.DataSheet4U.net Spec. No.: Version: Total pages: Date: MDGD084-SN05-0 0.2 23 2004- March-15 AU OPTRONICS CORPORATION Product Functional Specifications 8.4 ” SVGA Color TFT-LCD Module Model Name: G084SN05 V.0 Approved by Prepared by Martin Sun Cynthia Lin GD- MDBU Marketing Division / AU Optronics Croporation Customer Checked & Approved by (C) Copyright AU Optroncis, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G084SN05 V.0 ver.0.2 1/23 w w w . D a t a S h e e t 4 U . n e t Version: 0.2 Total Pages: 23 Date: 2004/03/15 Product Functional Specification 8.4 inch SVGA Color TFT LCD Module Model Name: G084SN05 V.0 (u ) Preliminary Specification ( ) Final Specification Note: This Specification is subject to change without notice. (C) Copyright AU Optroncis, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G084SN05 V.0 ver.0.2 2/23 www.DataSheet4U.net I. Contents 1.0 Handling Precautions 2.0 General Description 2.1 Characteristics 2.2 Functional Block Diagram 3.0 Absolute Maximum Ratings 4.0 Optical Characteristics 5.0 Signal Interface 5.1 Connectors 5.2 Signal Pin 5.3 Signal Description 5.4 Signal Electrical Characteristics 5.5 Signal for Lamp Connector 6.0 Pixel Format Image 7.0 Parameter Guide Line CFL Inverter 8.0 Interface Timings 8.1 Timing Characteristics 8.2 Timing Definition 9.0 Power Consumption 10.0 Power ON/OFF Sequence 11.0 Mechanical Characteristics (C) Copyright AU Optroncis, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G084SN05 V.0 ver.0.2 3/23 www.DataSheet4U.net II. Record of Revision Version and Date 0. 2004/02/03 0.1 2004/2/10 Page All 15 22 0.2 2004/3/15 11 Old Description First Draft All Update CCFL spec. Add drawing (back side) Lamp connectors Part Number Correction 15 20 22,23 CN2 Pin 1 à L, Pin 3 à H CN2 Pin 1à H, Pin 3 à L PDD & IDD updated Drawing updated New Description Remark (C) Copyright AU Optroncis, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G084SN05 V.0 ver.0.2 4/23 www.DataSheet4U.net 1.0 Handing Precautions 1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnection from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) In case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT module may be damaged. 10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the interface Connector of the TFT module. 11) After installation of the TFT module into an enclosure, do not twist nor bend the TFT module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may be damaged. 12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or regulations for disposal. 13) Small amount of materials having no flammability grade is used in the LCD module should be supplied by power complied with requirements of Limited Power Source, or be applied exemption. 14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit. Do not connect the CFL in Hazardous Voltage Circuit. (C) Copyright AU Optroncis, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G084SN05 V.0 ver.0.2 5/23 www.DataSheet4U.net 2.0 General Description This specification applies to the 8.4 inch color TFT LCD module G084SN05 V.0. This module is designed for display units for Industrial Applications. The screen format is intended to support the SVGA (800(H) x 600(V)) screen and 262k colors (RGB 6-bits data driver). All input signals are LVDS interface compatible. The module does not contain an inverter card for backlight. 2.1 Display Characteristics The following items are characteristics summary on the table under 25℃ condition: Items Screen Diagonal Active Area Pixel H x V Pixel Pitch Pixel Arrangement Display Mode Typical White Luminance (ICFL=6 mA) Contrast Ratio Optical Rise Time/Fall Time Nominal Input Voltage VDD Typical Power Consumption (VDD line + VCFL line) Weight Physical Size Electrical Interface Support Color Temperature Range.


B133EW01-V2 G084SN05-V0 G084SN05-V1


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)