Document
SEMICONDUCTORS
TIC226A, TIC226B, TIC226C, TIC226D, TIC226E, TIC226M, TIC226N, TIC226S
SILICON BIDIRECTIONAL TRIODE THYRISTOR
• • • • • • • 8 A RMS 70 A Peak Glass Passivated Wafer 100 V to 800 V Off-State Voltage Max IGT of 50 mA (Quadrants 1-3) High-temperature, High-current and high-voltage applications Compliance to ROHS
DESCRIPTION This device is a bidirectional triode thyristor (triac) which may be triggered from the off-state to the on-state by either polarity of gate signal with main Terminal 2 at either polarity. ABSOLUTE MAXIMUM RATINGS Value A
VDRM
Symbol
Ratings B C
Unit M S N
V A A A A W W °C °C °C
D
E
Repetitive peak off-state voltage 100 200 300 400 500 600 700 800 (see Note1) Full-cycle RMS on-state current at (or 8 IT(RMS) below) 70°C case temperature (see note2) Peak on-state surge current full-sine-wave 70 ITSM (see Note3) Peak on-state surge current half-sine-wave 8 ITSM (see Note4) Peak gate current ±1 IGM Peak gate power dissipation at (or below) 85°C case temperature (pulse width ≤200 2.2 PGM µs) Average gate power dissipation at (or 0.9 PG(AV) below) 85°C case (see Note5) www.DataSheet4U.com Operating case temperature range -40 to +110 TC Storage temperature range -40 to +125 Tstg Lead temperature 1.6 mm from case for 10 230 TL seconds
Page 1 of 3
SEMICONDUCTORS
TIC226A, TIC226B, TIC226C, TIC226D, TIC226E, TIC226M, TIC226N, TIC226S
Notes: 1. 2. 3. 4. 5. These values apply bidirectionally for any value of resistance between the gate and Main Terminal 1. This value applies for 50-Hz full-sine-wave operation with resistive load. Above 85°C derate linearly to 110°C case temperature at the rate of 320 mA/°C. This value applies for one 50-Hz full-sine-wave when the device is operating at (or below) the rated value of on-state current. Surge may be repeated after the device has returned to original thermal equilibrium. During the surge, gate control may be lost. This value applies for one 50-Hz half-sine-wave when the device is operating at (or below) the rated value of on-state current. Surge may be repeated after the device has returned to original thermal equilibrium. During the surge, gate control may be lost. This value applies for a maximum averaging time of 20 ms.
THERMAL CHARACTERISTICS Symbol
R∂JC R∂JA
Ratings
Junction to case thermal resistance Junction to free air thermal resistance
Value
≤ 1.8 ≤ 62.5
Unit
°C/W
ELECTRICAL CHARACTERISTICS
TC=25°C unless otherwise noted
Symbol
IDRM
Ratings
Repetitive peak offstate current Gate trigger current
Test Condition(s) VD = Rated VDRM, , IG = 0, TC = 110°C Vsupply = +12 V†, RL = 10 Ω, tp(g) = > 20 µs Vsupply = +12 V†, RL = 10 Ω, tp(g) = > 20 µs Vsupply = -12 V†, RL = 10 Ω, tp(g) = > 20 µs Vsupply = -12 V†, RL = 10 Ω, tp(g) = > 20 µs Vsupply = +12 V†, RL = 10 Ω, tp(g) = > 20 µs Vsupply = +12 V†, RL = 10 Ω, tp(g) = > 20 µs Vsupply = -12 V†, RL = 10 Ω, tp(g) = > 20 µs Vsupply = -12 V†, RL = 10 Ω, tp(g) = > 20 µs Vsupply = +12 V†, IG = 0, initiating ITM = 100 mA Vsupply = -12 V†, IG = 0, initiating ITM = -100 mA
Min Typ
±5 2 -12 -9 20 0.7 -0.8 -0.8 0.9 5 -9 ±1.6 ±100 -
Mx Unit
±2 50 -50 -50 2 -2 -2 2 30 mA -30 50 -50 ±2.1 V/µs mA V mA
IGT
mA
VGT
Gate trigger voltage
V
IH
Holding current
IL
www.DataSheet4U.com VTM
Latching current Peak on-state voltage Critical rate of rise of off-state voltage Critical rise of communication voltage
dv/dt dv/dt©
Vsupply = +12 V† (seeNote7) Vsupply = -12 V† (seeNote7) ITM = ± 12 A, IG = 50 mA (see Note6) VDRM = Rated VDRM, IG = 0 TC = 110°C VDRM = Rated VDRM, ITRM = ± 12A TC = 85°C
† All voltages are whit respect to Main Terminal 1. Page 2 of 3
SEMICONDUCTORS
TIC226A, TIC226B, TIC226C, TIC226D, TIC226E, TIC226M, TIC226N, TIC226S
Note 6: This parameters must be measured using pulse techniques, tW = ≤1ms, duty cycle ≤ 2 %, voltage-sensing contacts, separate from the courrent-carrying contacts are located within 3.2mm (1/8 inch) from de device body. Note 7: The triacs are triggered by a 15-V (open circuit amplitude) pulse supplied by a generator with the following characteristics : RG = 100Ω, tp(g) = 20 µs, tr = ≤ 15ns, f = 1 kHz.
MECHANICAL DATA CASE TO-220
Pin 1 : Pin 2 : Pin 3 :
www.DataSheet4U.com
Main Terminal 1 Main Terminal 2 Gate
Page 3 of 3
.