Document
SD7401
SIX-CHANNEL AUDIO AMPLIFIER
DESCRIPTION
SD7401 is a 6-channel audio amplifier with built-in microphone input amplifier. High quality audio output is available through simple peripheral circuit and the amplifier gain can be adjusted flexibly by external resistor. It is widely used as pre-amplification in various multi-channel audio systems.
FEATURES
* BICMOS technology * Dual power supply (+5V/-12V) * Built-in voltage regulation module * Low distortion * Standby function * Mute function * ON/OFF POP noise suppression
SSOP-20-225-0.65
APPLICATIONS
* Audio amplification system, such as VCD/DVD
ORDERING INFORMATION
Part No. SD7401 Package SSOP-20-225-0.65 Marking SD7401
BLOCK DIAGRAM
www.DataSheet4U.com
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http://www.silan.com.cn
REV:1.0
2008.07.07 Page 1 of 7
SD7401
ABSOLUTE MAXIMUM RATINGS (Unless otherwise specified, Tamb = 25°C)
Characteristics Supply Voltage (VCC-Vss) Operating Temperature Storage Temperature supply. Symbol VCC/VSS Topr Tstg Rating +6/-1
Unit V °C °C
-20~85 -40~125
Note 1: Tolerable voltage is decided by external resistor because of built-in voltage regulator at negative power
ELECTRICAL CHARACTERISTIC (Unless otherwise specified, VCC = 5V, VSS = -12V, RL = 10kΩ, Tamb =
25°C, f = 1kHz) Characteristics Operating Voltage Symbol VCC VSS ICC Operating Current Standby Current Max. Output Voltage Audio Amplitude Response Voltage Gain Total Harmonic Distortion
www.DataSheet4U.com Signal-Noise Ratio
Test Condition
Min. --2.0
Typ. 5 -12 2.2 14.8 600 2.51 8.3 11.5 0.05 76 79 77 65 -27.6
Max. --2.5 14.9 640 2.53 8.5 -0.06 78 80 80 70 0.2 --
Unit V V mA mA µA Vrms dB dB dB dB dB dB dB dB Ω
ISS ISTBY Vomax
External resistor 470Ω at negative power supply STBY_N connect toVSS fin=1kHz; RL=10kΩ; THD=0.1% 20Hz~20kHz, Vo=2Vrms No input resistor, THD=0.1% fin=1kHz; RL=10kΩ; Vo=2Vrms fin=1kHz; RL=10kΩ; Vo=2Vrms fin=1kHz, Vin=-60dB fin=1kHz; RL=10kΩ; Vo=2Vrms fin=1kHz; RL=10kΩ; Vo=2Vrms fin=1kHz; RL=10kΩ; Vo=2Vrms fin=1kHz, RL=10kΩ
14.7 550 2.50 7.7 --75 78 75 62 ---
G THD SNR DR MR CT CB Ri
Dynamic Range Mute Restrain Channel Separation Channel Balance Input Impedance
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http://www.silan.com.cn
REV:1.0
2008.07.07 Page 2 of 7
SD7401
PIN CONFIGURATION
PIN DESCRIPTION
Pin No. 1 2 3 4 5 6 7 8 9
www.DataSheet4U.com 10
Pin Name VCC PMUTE MIC IN MUTE CENT IN LS IN L IN R IN SUB IN RS IN RS OUT SUB OUT R OUT L OUT LS OUT CENT OUT MIC OUT STBY_N VSS GND
I/O -I/O I I I I I I I I O O O O O O O I ---
Pin Description Positive power supply POP restrain control Microphone input Mute control Center input Left surround input Left channel input Right channel input Subwoofer input Right surround input Right surround output Subwoofer output Right channel output Left channel output Left surround output Center output Microphone output Standby control Negative power supply Ground
11 12 13 14 15 16 17 18 19 20
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http://www.silan.com.cn
REV:1.0
2008.07.07 Page 3 of 7
SD7401
FUNCTION DESCRIPTION
1. Channel amplifier
The second-order filter structure shown as above is adopted for 6-channel audio amplifier, with in-band gain of about 12dB and -3dB bandwidth of 40kHz above which is well meet audio requirements. As principle structure, in-band gain is decided by: G = − R 2 , thus, gain can be adjusted by changing R1.
R1
2.
Microphone amplifier
R2
C
www.DataSheet4U.com
VCC R1 MICIN
+
VSS
MICOUT
AGND
The proportional amplifier shown as above is adopted for microphone amplifier with setting gain of about 29dB, and capacitor c is used for high frequency signal filtering. As described above, the gain can be also adjusted by changing R1. 3. Mute & ON/OFF POP noise control
Mute control pin (pin 4) controls 6-channel as mute by internal switches. It comes to mute mode when pin 4 is
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http://www.silan.com.cn
REV:1.0
2008.07.07 Page 4 of 7
SD7401
connected to Vcc (high level) and comes to normal mode when connected to ground. Pin 2 is used for POP noise restrain by connecting an external capacitor which can be increased appropriately for better POP noises restrain effect. In general, POP noise restrain is realized by mute control. Mute pulse is generated when turned on for zero output and ended after powered on for normal output; mute pulse is also generated when power supply is threshold value below during turned off for zero output. Thus, pop noise is restrained during power on/down. 4. Power supply
The built-in voltage regulator for negative power supply is shown as below. An external resistor R guarantees voltage stability near -5 V on pin 19 and the chip power supply is ±5V for normal operation. Because the negative power to provide current is decided by this resistance, if the system output is light load, this resistance can be properly increased to reduce operate current, but the voltage of PIN 19 must be maintained and can not drop .