Document
MAX9060–MAX9064
EVALUATION KIT AVAILABLE
Ultra-Small, Low-Power Single Comparators in 4-Bump UCSP and 5 SOT23
General Description
The MAX9060–MAX9064 are small single comparators, ideal for a wide variety of portable electronics applications such as cell phones, media players, and notebooks that have extremely tight board space and power constraints. These comparators are offered in both, a miniature 4-bump UCSP™ package with a 1mm x 1mm footprint (as small as two 0402 resistors), and a 5-pin SOT23 package.
The MAX9060–MAX9064 feature an input voltage range of -0.3V to +5.5V independent of supply voltage. These devices maintain high impedance at the inputs even when powered down (VCC or VREF = 0V). They also feature internal filtering to provide high RF immunity.
The MAX9060 and MAX9061 have open-drain outputs and draw quiescent supply current from a user-supplied reference voltage, VREF, between 0.9V and 5.5V. These devices consume only 100nA (max) supply current and operate over the extended -40°C to +85°C temperature range.
The MAX9062, MAX9063 and MAX9064 are single comparators with an internal 0.2V reference. These devices feature either a push-pull or an open-drain output. They consume only 700nA (max) supply current. The MAX9062, MAX9063, and MAX9064 operate down to VCC = 1V over the extended -40°C to +85°C temperature range.
Applications
●● Cell Phones ●● Portable Media Players ●● Electronic Toys ●● Notebook Computers ●● Portable Medical Devices
Selector Guide and Typical Operating Circuits appears at end of data sheet.
Pin Configurations
TOP VIEW (BUMPS ON BOTTOM)
OUT A1
A2 IN
Features
●● Tiny 1mm x 1mm x 0.6mm 4-Bump UCSP ●● Footprint = Two 0402 Resistors ●● Also Available in a 5-Pin SOT23 Package ●● Ultra-Low Operating Current (100nA max) ●● Input Voltage Range = -0.3V to +5.5V ●● External REF Range = 0.9V to 5.5V
(MAX9060/MAX9061) ●● Internal REF Voltage = 0.2V
(MAX9062/MAX9063/MAX9064) ●● 15μs Propagation Delay ●● -40°C to +85°C Extended Temperature Range
Ordering Information
PART
PIN PACKAGE
TOP MARK
MAX9060EBS+G45
4 UCSP
AFX
MAX9060EUK+
5 SOT23
AFFG
MAX9061EBS+G45
4 UCSP
AFY
MAX9061EUK+
5 SOT23
AFFH
MAX9062EBS+G45
4 UCSP
AFZ
MAX9062EUK+
5 SOT23
AFFI
MAX9063EBS+G45
4 UCSP
AFA
MAX9063EUK+
5 SOT23
AFFJ
MAX9063EUK/V+T
5 SOT23
+AMGH
MAX9064EBS+G45
4 UCSP
AFB
MAX9064EUK+
5 SOT23
AFFK
Note: All devices are specified over the extended -40°C to+85°C operating temperature range. +Denotes a lead(Pb)-free/RoHS-compliant package. /V denotes an automotive qualified device. T = Tape and reel. G45 = Protective die coating.
UCSP is a trademark of Maxim Integrated Products, Inc.
REF (VCC)
1
+
5 OUT
MAX9060–MAX9064
GND 2
MAX9060– MAX9064
REF (VCC)
B1
B2 GND
GND 3
4 IN
UCSP
REF = MAX9060/MAX9061 (VCC) = MAX9062–MAX9064
SOT23
19-4105; Rev 6; 12/14
MAX9060–MAX9064
Ultra-Small, Low-Power Single Comparators in 4-Bump UCSP and 5 SOT23
Absolute Maximum Ratings
VCC, REF, IN to GND...............................................-0.3V to +6V OUT to GND (MAX9060–MAX9063)........................-0.3V to +6V OUT to GND (MAX9064 Only)............... -0.3V to + (VCC + 0.3V) Output Short-Circuit Current Duration.................................... 10s Input Current into Any Terminal.........................................±20mA Continuous Power Dissipation 4-Bump UCSP (derate 3.0mW/°C above +70°C)......... 238mW 5-Pin SOT23 (derate 3.9mW/°C above +70°C)........... 312mW
Operating Temperature Range.............................-40°C to +85°C Junction Temperature....................................................... +150°C Storage Temperature Range..............................-65°C to +150°C Lead Temperature (excluding UCSP, soldering, 10s)...... +300°C Soldering Temperature (reflow)........................................ +260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
MAX9060/MAX9061 Electrical Characteristics
(VREF = 1.8V, RPULLUP = 10kΩ to VPULLUP = 3.3V, TA = -40°C to +85°C. Typical values are at TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER DC CHARACTERISTICS Input Offset Voltage (Note 2) Hysteresis Input Voltage Range Input Bias Current Input Shutdown Current
Output Voltage Low
Output Leakage Current (OUT = High) AC CHARACTERISTICS Propagation Delay Fall Time REF SUPPLY REF Voltage
REF Input Current
REF Rejection Ratio Power-Up Time
SYMBOL
CONDITIONS
VOS
TA = +25°C
VHYS VIN IIN IIN_PD
VOL
(Note 3)
0V < VIN < VREF + 0.6V VREF + 0.6V < VIN < 5.5V VREF = 0V, VIN = 5.5V (Note 4) ISINK = 25µA, VREF = 0.9V, TA = +25°C ISINK = 200µA, VREF = 1.2V ISINK = 500µA, VREF = 1.8V ISINK = 1.2mA, VREF = 5.5.