DatasheetsPDF.com

NX3L1G66 Dataheets PDF



Part Number NX3L1G66
Manufacturers NXP Semiconductors
Logo NXP Semiconductors
Description Low-voltage analog switch
Datasheet NX3L1G66 DatasheetNX3L1G66 Datasheet (PDF)

NX3L1G66 Low-ohmic single-pole single-throw analog switch Rev. 8 — 9 November 2011 Product data sheet 1. General description The NX3L1G66 is a low-ohmic single-pole single-throw analog switch. It has two input/output terminals (Y and Z) and an active HIGH enable input pin (E). When E is LOW, the analog switch is turned off. Schmitt trigger action at the enable input (E) makes the circuit tolerant to slower input rise and fall times. The NX3L1G66 allows signals with amplitude up to VCC to be .

  NX3L1G66   NX3L1G66


Document
NX3L1G66 Low-ohmic single-pole single-throw analog switch Rev. 8 — 9 November 2011 Product data sheet 1. General description The NX3L1G66 is a low-ohmic single-pole single-throw analog switch. It has two input/output terminals (Y and Z) and an active HIGH enable input pin (E). When E is LOW, the analog switch is turned off. Schmitt trigger action at the enable input (E) makes the circuit tolerant to slower input rise and fall times. The NX3L1G66 allows signals with amplitude up to VCC to be transmitted from Y to Z; or from Z to Y. Its low ON resistance (0.5 ) and flatness (0.13 ) ensures minimal attenuation and distortion of transmitted signals. 2. Features and benefits  Wide supply voltage range from 1.4 V to 4.3 V  Very low ON resistance (peak):  1.6  (typical) at VCC = 1.4 V  1.0  (typical) at VCC = 1.65 V  0.55  (typical) at VCC = 2.3 V  0.50  (typical) at VCC = 2.7 V  0.50  (typical) at VCC = 4.3 V  High noise immunity  ESD protection:  HBM JESD22-A114F Class 3A exceeds 7500 V  MM JESD22-A115-A exceeds 200 V  CDM AEC-Q100-011 revision B exceeds 1000 V  IEC61000-4-2 contact discharge exceeds 4000 V for switch ports  CMOS low-power consumption  Latch-up performance exceeds 100 mA per JESD 78 Class II Level A  Direct interface with TTL levels at 3.0 V  Control input accepts voltages above supply voltage  High current handling capability (350 mA continuous current under 3.3 V supply)  Specified from 40 C to +85 C and from 40 C to +125 C 3. Applications  Cell phone  PDA  Portable media player NXP Semiconductors NX3L1G66 Low-ohmic single-pole single-throw analog switch 4. Ordering information Table 1. Ordering information Type number Package Temperature range Name Description NX3L1G66GW 40 C to +125 C TSSOP5 plastic thin shrink small outline package; 5 leads; body width 1.25 mm NX3L1G66GM 40 C to +125 C XSON6 plastic extremely thin small outline package; no leads; 6 terminals; body 1  1.45  0.5 mm Version SOT353-1 SOT886 5. Marking Table 2. Marking codes[1] Type number NX3L1G66GW NX3L1G66GM Marking code DL DL [1] The pin 1 indicator is located on the lower left corner of the device, below the marking code. 6. Functional diagram E Z Fig 1. Logic symbol Y 001aag487 7. Pinning information 7.1 Pinning NX3L1G66 Y1 5 VCC Z2 GND 3 4E 001aai590 Fig 3. Pin configuration SOT353-1 (TSSOP5) Y E Fig 2. Logic diagram Z 001aah372 NX3L1G66 Y1 6 VCC Z2 5 n.c. GND 3 4E 001aah444 Transparent top view Fig 4. Pin configuration SOT886 (XSON6) NX3L1G66 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 — 9 November 2011 © NXP B.V. 2011. All rights reserved. 2 of 19 NXP Semiconductors NX3L1G66 Low-ohmic single-pole single-throw analog switch 7.2 Pin description Table 3. Symbol Y Z GND E n.c. VCC Pin description Pin SOT353-1 1 2 3 4 5 SOT886 1 2 3 4 5 6 8. Functional description Description independent input or output independent output or input ground (0 V) enable input (active HIGH) not connected supply voltage Table 4. Input E L H Function table[1] [1] H = HIGH voltage level; L = LOW voltage level. 9. Limiting values Switch OFF-state ON-state Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Max Unit VCC supply voltage VI input voltage enable input E VSW switch voltage IIK input clamping current VI < 0.5 V ISK switch clamping current VI < 0.5 V or VI > VCC + 0.5 V ISW switch current VSW > 0.5 V or VSW < VCC + 0.5 V; source or sink current 0.5 [1] 0.5 [2] 0.5 50 - +4.6 V +4.6 V VCC + 0.5 V - mA 50 mA 350 mA VSW > 0.5 V or VSW < VCC + 0.5 V; pulsed at 1 ms duration, < 10 % duty cycle; peak current - 500 mA Tstg storage temperature Ptot total power dissipation Tamb = 40 C to +125 C 65 [3] - +150 C 250 mW [1] The minimum input voltage rating may be exceeded if the input current rating is observed. [2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not exceed 4.6 V. [3] For TSSOP5 package: above 87.5 C the value of Ptot derates linearly with 4.0 mW/K. For XSON6 package: above 118 C the value of Ptot derates linearly with 7.8 mW/K. NX3L1G66 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 — 9 November 2011 © NXP B.V. 2011. All rights reserved. 3 of 19 NXP Semiconductors NX3L1G66 Low-ohmic single-pole single-throw analog switch 10. Recommended operating conditions Table 6. Recommended operating conditions Symbol Parameter Conditions VCC VI VSW Tamb t/V supply voltage input voltage switch voltage ambient temperature input transition rise.


NX3L1G3157 NX3L1G66 NX3L1T3157


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)