Document
CAMEL TECHNOLOGY
PLASTIC FILM CAPACITORS
M E TA L L I Z E D P O LY P R O P Y L E N E F I L M PA C I T O R
Outline Drawing
Loose W max T max W H H max Taped T 103J © 1 0 0VMPP
MPP
Radial dipped Appearance
104J© 2 5 0VMPP
Construction
474J © 400VMPP
25 min
www.DataSheet4U.com
P±1.0
Direct welding Single side metallized Ød±00.5 P
MPP are constructed with metallized polypropylene film dielectric ,copperply lead and epoxy resin powder coating. They are suitable for blocking, by-pass, coupling, decoupling, filtering, timing, tuning temperature compensation, and ideal for use in telecommunication equipments, data processing equipments, industrial instruments, automatic control system and other general electronic equipments.
Widely used in high frequency, DC, AC and pulse circuits SPECIFICATION: 1. OPERATING TEMPERATURE: -40℃~85℃ 2. CAPACITANCE RANGE:0.01µF~3.3µF 3. CAPACITANCE TOLERANCE:±5%(J),±10%(K), ±20%(M) 4. RATED VOLTAGE(RV): 100VDC, 250VDC, 400VDC,630VDC 5. DISSIPATION FACTOR: 0.1% MAX AT 1KHZ, 25℃ 6. INSULATION RESISTANCE(IR):>30000 MΩ (C≦0.33µF) >10000 MΩ·µF (C>0.33µF)
FEATURES: Low loss at high frequency Small inherent temperature rise Flame retardant epoxy resin powder coating (UL94/V-0) PERFORMANCE
Test Characteristics Withstand voltage: Between terminals Withstand voltage: Between terminals & enclosure Insulation resistance: Between terminals Insulation resistance: Between terminals & enclosure Heat proof: Insulation resistance at 85℃ Heat proof: Rate of variation of capacitance at 85℃ Humidity test: Appearance Humidity test: Withstand voltage Humidity test: Insulation resistance Humidity test: Dissipation factor Humidity test: Rate of variation capacitance Reference Standard
Test Methods JIS C 5102 Apply 2.0 times of rated voltage for 60 sec. charge discharge current must be 1A max Apply 2.0 times of rated voltage for 1 to 5 sec Apply rated voltage ±15% for 60 sec. when rated voltage under 100V. Apply 100V ±15% when rated voltage from 100V to 500V at 20℃ Testing temperature: 85±2℃.
Performance Shall be no abnormality Shall be no abnormality ≤0.33µF ≧45,000MΩ >0.33µF ≧15,000MΩ•µF ≤0.33µF≧4500MΩ at 85℃ >0.33µF≧1500MΩ•F at 85℃ 0% Within-5% of the value before test Shall be no abnormality
Temperature: 40±2℃; Humidity: 90-95% RH +24 Testing time: 500 - 0 Hrs. Apply voltage: rated voltage. After testing, leave it for about 16 Hrs. at standard condition Withstand voltage is 175% rated voltage, 60 sec. GB 10190( IEC 60384-16) / JIS 5102
Shall be no abnormality ≤0.33µF≧15000MΩ >0.33µF≧5000MΩ•µF 0.0015 (0.15%) Max. Within ±5% of the value before test
56
CAMEL TECHNOLOGY
PLASTIC FILM CAPACITORS
M E TA L L I Z E D P O LY P R O P Y L E N E F I L M PA C I T O R
DIMENSIONS:
Part No.
MPP103□2AA1-7□□□□□
MPP
Radial dipped
100VDC Dimensions(mm) Cap dv/dt (µF) W H T P dФ V/µs
0.01 0.015 0.022 0.033 0.047 0.068 0.1 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 11.0 12.5 11.0 13.0 11.0 11.0 11.0 11.0 11.0 13.0 13.0 19.0 19.0 19.0.