Document
www.DataSheet4U.com
Main Features
• • • • •
High Sensitivity and High SNR Performance 1/2" CMOS Sensor Total Resolution of 1.3M (with 5 µm Square Pixels) High Data Rate: 75 Mpixels/s Provides 60 Frame/s at 1M Resolution (for 1M60) CameraLink® Data Format (Base Configuration - 1 Channel) Flexible and Easy to Operate via Serial Communication Control – Gain: 0 dB to 18 dB in 3 dB Steps – Dynamic Range: 8, 10 or 12-bit Data – Contrast Expansion – Shutter Time Pogrammable – Subsampling: 1/4 and 1/16 Resolution – Trigger Mode: Free-run or External Trigger Mode – Programmable ROI – Test Pattern Column FPN Correction Programmable Look-up Table Single Power Supply: DC 12 V to 24 V Provided on Hirose-6 Connector Input TTL Trigger Signal and Output TTL Shutter Signal on Hirose-5 Connector Compact Design: 44 × 44 × 45 mm (w, h, l) C-mount Adapter High Reliability - CE and FCC Compliant
CameraLink® Areascan Cameras ATMOS™ 1M60 ATMOS™ 1M30
• • • • • • •
Product Description
This camera features an outstanding sensitivity and SNR, even at maximal speeds. The ROI allows to increase the frame rate (for instance, 175 fps in VGA format 1M60). ATMOS™ cameras are based on a rolling shutter CMOS sensor. The configuration interface provides access to advanced functions (contrast expansion, image calibration, LUT). The versatile and compact mechanical housing enables you to implement various configurations. These features combined with a compelling price, make ATMOS an attractive alternative for users of megapixel cameras.
Preliminary
Applications
High-speed, SNR performance and reliability of this camera make it suitable for machine vision, especially: • Material Inspection (e.g. glass, IC, PCB) • Robot Guidance • Metrology and various applications like: • Microscopy • Surveillance Demanding Tasks
5429B–IMAGE–04/05
www.DataSheet4U.com
1. Typical Performances
Table 1-1. Camera Typical Performances
Sensor Characteristics at Maximum Pixel Rate 1M60 Resolution H × V Pixel size (square) Maximum frame rate Pixel rate Camera Performances Bit depth Spectral range Linearity PRNU FPN Responsivity Output RMS Noise Dynamic range Conversion factor Dark Current Over Illumination Behavior Mechanical and Electrical Interface Size (w × h × l) Weight Lens Mount 44 × 44 × 45 115 C-mount ∆x, y = ± 250 ∆z = ±150 ∆0xy = ± 0.7 ∆tiltz = 0-200 single 12 to 24 <2 0 to 55 (non-condensing) -40 to 70 (non-condensing) µm µm degree µm VDC W °C °C mm g 8, 10 or 12 350–1000 ±2% in 5% and 95% of FSR 1.5% rms 0.1% rms 10000 (1) < 2.7 LSB rms > 63 10 1500 75 Esat
(2)
1M30 1312 × 1024 5×5 24 37.5
Unit Pixels µm Hz MHz
1312 × 1024 5×5 48 75
Bits nm
LSB/(Lux.s) dB e-/ LSB e-/s
Sensor Alignment
Power supply Power consumption Operating temperature Storage temperature
Measured with light source 3200°K and IR filter Warning:
1. When exposed to such illumination level the sensor might lock-up and should be reset See Register Software Reset @ 206H, Internal Register Mapping on page 17
2
ATMOS -1M60/1M30 [Preliminary]
5429B–IMAGE–04/05
www.DataSheet4U.com
[Preliminary] ATMOS -1M60/1M30
Figure 1-1. Responsivity Diagram
Responsivity at 0 dB Gain 50 45 40 35
LSB/( nJ/cm2)
30 25 20 15 10 5 0 300 400 500 600 700 nm 800 900 1000 1100
Figure 1-2.
Quantum Efficiency
Quantum Efficiency
0,8 0,7 0,6
QE (%)
0,5 0,4 0,3 0,2 0,1 0 400
500
600
700
800
900
1000
Wavelength (nm)
3
5429B–IMAGE–04/05
www.DataSheet4U.com
2. Standard Conformity
The cameras have been tested in the following conditions: • Camera with complete Atmel housing • Shielded power supply cable • CameraLink data transfer cable ref. 14B26-SZLB-500-OLC (3M™) • Linear AC-DC power supply Atmel recommends using the same configuration to ensure compliance with the following standards.
2.1
CE Conformity
The ATMOS cameras comply with the European directive 89/336/CEE (EN55022 A/CISPR22 A, EN55024, EN61000-6-2).
2.2
FCC conformity
ATMOS Cameras comply with Part 15 of FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate.