DatasheetsPDF.com

XRT79L73 Dataheets PDF



Part Number XRT79L73
Manufacturers Exar Corporation
Logo Exar Corporation
Description 3-CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
Datasheet XRT79L73 DatasheetXRT79L73 Datasheet (PDF)

www.DataSheet4U.com PRELIMINARY LINE INTERFACE U NIT XRT79L73 REV. P1.0.0 3 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC JUNE 2004 HARDWARE MANUAL The XRT79L73 is a three channel, ATM UNI/PPP Physical Layer Processor with integrated DS3/E3 framing controllers and Line Interface Units with Jitter Attenuators that are designed to support ATM direct mapping and cell delineation as well as PPP mapping and Frame processing. For ATM UNI applications, this device provides the ATM Physical Layer (Physical .

  XRT79L73   XRT79L73


Document
www.DataSheet4U.com PRELIMINARY LINE INTERFACE U NIT XRT79L73 REV. P1.0.0 3 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC JUNE 2004 HARDWARE MANUAL The XRT79L73 is a three channel, ATM UNI/PPP Physical Layer Processor with integrated DS3/E3 framing controllers and Line Interface Units with Jitter Attenuators that are designed to support ATM direct mapping and cell delineation as well as PPP mapping and Frame processing. For ATM UNI applications, this device provides the ATM Physical Layer (Physical Medium Dependent and Transmission Convergence sub-layers) interface for the public and private networks at DS3/E3 rates. For Clear-Channel Framer applications, this device supports the transmission and reception of “user data” via the DS3/E3 payload. The XRT79L73 includes DS3/E3 Framing, Line Interface Unit with Jitter Attenuator that supports mapping of ATM or HDLC framed data. A flexible parallel microprocessor interface is provided for configuration and control. Industry standard UTOPIA II and POS-PHY interface are also provided. GENERAL FEATURES: • On chip Clock and Data Recovery circuit for high input jitter tolerance • Meets E3/DS3 Jitter Tolerance Requirements • Detects and Clears LOS as per G.775. • Receiver Monitor mode handles up to 20 dB flat loss with 6 dB cable attenuation • Compliant with jitter transfer template outlined in ITU G.751, G.752, G.755 and GR-499-CORE,1995 standards • Meets ETSI TBR 24 and GR-499 Jitter Transfer Requirements • On chip B3ZS/HDB3 encoder and decoder that can be either enabled or disabled • On-chip clock synthesizer provides the appropriate rate clock from a single 12.288 MHz Clock • Integrated T3/E3 Line Interface Unit • Integrated Jitter Attenuator that can be selected either in Receive or Transmit path • On chip advanced crystal-less Jitter Attenuator • Jitter Attenuator can be selected in Receive or Transmit paths • Flexible integrated Clock Multiplier that takes single frequency clock and generates either DS3 or E3 frequency. • 16 or 32 bits selectable FIFO size • Meets the Jitter and Wander specifications described in T1.105.03b,ETSI TBR-24, Bellcore GR-253 and GR-499 standards • 8/16 bit UTOPIA Level I and II and PPP Multi-PHY Interface operating at 25, 33 or 50 MHz. • Jitter Attenuator can be disabled • Maximum power consumption 3.1W DS3/E3 FRAMER • HDLC Controller that provides the mapping/ extraction of either bit or byte mapped encapsulated packet from DS3/E3 Frame. • Contains on-chip 16 cell FIFO (configurable in depths of 4, 8, 12 or 16 cells), in both the Transmit (TxFIFO) and Receive Directions (RxFIFO) • DS3 framer supports both M13 and C-bit parity. • DS3 framer meets ANSI T1.107 and T1.404 standards. • Contains on-chip 54 byte Transmit and Receive OAM Cell Buffer for transmission, reception and processing of OAM Cells • Detects OOF,LOF,AIS,RDI/FERF alarms. • Generation and Insertion of FEBE on received parity errors supported. • Supports ATM cell or PPP Packet Mapping • Supports M13 and C-Bit Parity Framing Formats • Supports DS3/E3 Clear-Channel Framing. • Includes PRBS Generator and Receiver • Supports Line, Cell, and PLCP Loop-backs • Interfaces to 8 Bit wide Intel, Motorola or PowerPC • Low power 3.3V, 5V Input Tolerant, CMOS • Available in 456 Lead PBGA Package • JTAG Interface • Automatic insertion of RDI/FERF on alarm status. • E3 framer meets G.832,G.751 standards. • Framers can be bypassed. ATM/PPP PROTOCOL PROCESSOR TRANSMIT CELL PROCESSING • • • • Extracts ATM cells Supports ATM cell payload scrambling Maps ATM cells into E3 or DS3 frame PLCP frame and mapping of ATM cell streams R ECEIVE CELL PROCESSING Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com XRT79L73 REV. P1.0.0 PRELIMINARY 3 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC ÿþ • Extraction of ATM cells from PLCP frame or directly from E3 or DS3 frame • 8/16 bit UTOPIA Level I and II and PPP Multi-PHY Interface operating at 25, 33 or 50 MHz. • Termination of PLCP frame • Supports payload cell de-scrambling TRANSMIT PACKET PROCESSING • Compliant with ATM Forum UTOPIA II interface • Programmable FIFO size for both Transmit and Receive direction • Inserts PPP packets into data stream • Maps HDLC data stream directly into DS3 or E3 frame • Compliant to POS-PHY Level 2 interface SERIAL INTERFACE • Serial clock and data interface for accessing DS3/ E3 framer • Extracts in-band messaging packets • Supports CRC-16/32, HDLC flag and Idle sequence generation RECEIVE PACKET PROCESSING • Serial clock and data interface for accessing cell/ packet processor APPLICATIONS • Extracts HDLC data stream from DS3 or E3 frame • Inserts in-band messaging packets • Detects and removes HDLC flags UTOPIA/ SYSTEM INTERFACE FIGURE 1. BLOCK DIAGRAM OF THE XRT79L73 • • • • Digital Access and Cross Connect Systems 3G Base Stations DSLAMs Digital, ATM, WAN and LAN Switches Channel 1 of 3 PLCP & Overhead TU-3 Clock & POH Data Processor .


XRT79L72 XRT79L73 XRT79L74


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)