DatasheetsPDF.com

PE4241 Dataheets PDF



Part Number PE4241
Manufacturers Peregrine Semiconductor
Logo Peregrine Semiconductor
Description SPDT UltraCMOS RF Switch
Datasheet PE4241 DatasheetPE4241 Datasheet (PDF)

www.DataSheet4U.com Product Specification PE4241 SPDT UltraCMOS™ RF Switch Product Description The PE4241 UltraCMOS™ RF Switch is designed to cover a broad range of applications from DC through 3.0 GHz. This reflective switch integrates on-board CMOS control logic with a low voltage CMOS-compatible control interface, and can be controlled using either single-pin or complementary control inputs. Using a nominal +3-volt power supply voltage, a typical input 1 dB compression point of +27 dBm can.

  PE4241   PE4241


Document
www.DataSheet4U.com Product Specification PE4241 SPDT UltraCMOS™ RF Switch Product Description The PE4241 UltraCMOS™ RF Switch is designed to cover a broad range of applications from DC through 3.0 GHz. This reflective switch integrates on-board CMOS control logic with a low voltage CMOS-compatible control interface, and can be controlled using either single-pin or complementary control inputs. Using a nominal +3-volt power supply voltage, a typical input 1 dB compression point of +27 dBm can be achieved. The PE4241 UltraCMOS™ RF Switch is manufactured in Peregrine’s patented Ultra Thin Silicon (UTSi®) CMOS process, offering the performance of GaAs with the economy and integration of conventional CMOS. Figure 1. Functional Diagram RFCommon Features • Single-pin or complementary CMOS logic control inputs • +3.0-volt power supply needed for single-pin control mode • Low insertion loss: 0.7 dB at 1.0 GHz, 0.9 dB at 2.0 GHz • Isolation of 30 dB at 1.0 GHz, 21 dB at 2.0 GHz • Typical input 1 dB compression point of +27 dBm • Ultra-small SOT23 package Figure 2. Package Type 6-lead SOT23 RF1 RF2 CMOS Control Driver CTRL CTRL or VDD Table 1. Electrical Specifications @ +25 °C, VDD = 3 V (ZS = ZL = 50 Ω) Parameter Operation Frequency Insertion Loss Isolation Return Loss ‘ON’ Switching Time ‘OFF’ Switching Time Video Feedthrough 2 1 Conditions 1000 MHz 2000 MHz 1000 MHz 2000 MHz 1000 MHz 2000 MHz 50% CTRL to 0.1 dB of final value, 1 GHz 50% CTRL to 25 dB isolation, 1 GHz Minimum DC Typical 0.7 Maximum 3000 0.85 1.05 Units MHz dB dB dB dB dB dB ns ns mVpp dBm dBm 28 19 18 16 0.9 30 21 20 18 300 200 15 Input 1 dB Compression Input IP3 2000 MHz 2000 MHz, 14 dBm input power 26 43 27 45 Notes: 1. Device linearity will begin to degrade below 10 MHz. 2. The DC transient at the output of any port of the switch when the control voltage is switched from Low to High or High to Low in a 50 Ω test set-up, measured with 1ns risetime pulses and 500 MHz bandwidth. Document No. 70-0094-01 │ www.psemi.com ©2005 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 8 PE4241 Product Specification Figure 3. Pin Configuration (Top View) pin 1 Table 3. Absolute Maximum Ratings Symbol Parameter/Conditions Power supply voltage Voltage on any input Storage temperature range Operating temperature range Input power (50Ω) ESD voltage (Human Body Model) Min -0.3 -0.3 -65 -40 Max 4.0 VDD+ 0.3 150 85 30 1500 Units V V °C °C dBm V RF1 GND RF2 1 6 CTRL or VDD RFC CTRL VDD VI TST TOP PIN . 4241 Pin Name RF1 GND RF2 CTRL RFC CTRL or VDD 2 5 3 4 Table 2. Pin Descriptions Pin No. 1 2 VESD Description RF1 port (Note 1) Ground connection. Traces should be physically short and connected to RF2 port (Note 1) Switch control input, CMOS logic level. Common RF port for switch (Note 1) This pin supports two interface options: Single-pin control mode. A nominal 3volt supply connection is required. Complementary-pin control mode. A complementary CMOS control signal to CTRL is supplied to this pin. Bypassing on this pin is not required in this mode. Table 4. DC Electrical Specifications Parameter VDD Power Supply VoltPower Supply Current (VDD = 3V, VCNTL = 3V) Control Voltage High Control Voltage Low 0.7x VDD 0.3x VDD Min 2.7 Typ 3.0 250 Max 3.3 500 Units V nA V V 3 4 5 6 Electrostatic Discharge (ESD) Precautions When handling this UltraCMOS™ device, observe the same precautions that you would use with other ESD-sensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the specified rating. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOS™ devices are immune to latch-up. Note 1: All RF pins must be DC blocked with an external series capacitor or held at 0 VDC. ©2005 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 8 Document No. 70-0094-01 │ UltraCMOS™ RFIC Solutions PE4241 Product Specification Table 5. Single-pin Control Logic Truth Table Control Voltages Pin 6 (CTRL or VDD) = VDD Pin 4 (CTRL) = High Pin 6 (CTRL or VDD) = VDD Pin 4 (CTRL) = Low Signal Path RFC to RF1 Control Logic Input The PE4241 is a very versatile RF CMOS switch that supports two operating control modes; singlepin control mode and complementary-pin control mode. Single-pin control mode enables the switch to operate with a single control pin (pin 4) supporting a +3-volt CMOS logic input, and requires a dedicated +3-volt power supply connection on pin 6 (VDD). This mode of operation reduces the number of control lines required and simplifies the switch control interface typically derived from a CMOS µProcessor I/O port. Complementary-pin control mode allows the switch to operate using complementary control pins CTRL and CTRL (pins 4 & 6), that can be directly driven by +3-volt CMOS logic or a suitable µProcessor I/O port. This enables the PE4241 to be used as a potential alternate source for SPDT RF switch products used.


PE4240 PE4241 PE4242


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)