DatasheetsPDF.com

IL9151-3 Dataheets PDF



Part Number IL9151-3
Manufacturers IK Semiconductor
Logo IK Semiconductor
Description Pulse Dialer
Datasheet IL9151-3 DatasheetIL9151-3 Datasheet (PDF)

TECHNICAL DATA IL9151-3 PULSE DIALER The IL9151-3 pulse dialer is a monolithic CMOS integrated circuit which converts pushbutton inputs to a series of pulses suitable for telephone dialing. It is intended to replace mechanical telephone dialers and can operate directly from telephone lines. CMOS technology is used to produced this device, resulting in very low power requirements and high noise immunity. The IL9151-3 can be easily interfaced with a variety of telephones, requiring only a minima.

  IL9151-3   IL9151-3



Document
TECHNICAL DATA IL9151-3 PULSE DIALER The IL9151-3 pulse dialer is a monolithic CMOS integrated circuit which converts pushbutton inputs to a series of pulses suitable for telephone dialing. It is intended to replace mechanical telephone dialers and can operate directly from telephone lines. CMOS technology is used to produced this device, resulting in very low power requirements and high noise immunity. The IL9151-3 can be easily interfaced with a variety of telephones, requiring only a minimal number of external components. • Direct telephone line operation • 4 x 3 matrix keyboard interface • Supply voltage range of 2.0 to 5.5 volts • Inexpensive RC oscillator • Low power standby mode for redialing • 22-digit redial memory • Redial with either * or # key • Dialer reset for line power breaks > 200 ms • Selectable make/break ratio • High speed test capacity ORDERING INFORMATION IL9151-3N Plastic TA = -20° to 70° C for package PIN ASSIGNMENT www.DataSheet4U.com LOGIC DIAGRAM KEYBOARD ASSIGNMENT R1 R2 R3 R4 1 2 3 4 5 6 7 8 9 * 0 # C1 C2 C3 (*,# : Redial) PIN 5 = VCC PIN 12 = GND ww.DataSheet4U.com IL9151-3 PIN DESCRIPTION PIN No. 1 2 3 4 14 15 16 5 12 6 7 8 NAME R1~R4 Key inputs. These inputs can be interfaced to either an XY matrix keyboard or a 2 of 7 type keyboard. The keypad inputs are normally held at high. When a key is depressed, scanning signals are presented at C1, C2, and C3 inputs; the dialer identifies the key by examining the R1~R4 inputs. Debouncing is provided to avoid false entry. Positive power supply input. Negative power supply input. Oscillator circuit input/output. The oscillator consists of two inverters, with oscillator frequency controlled by external RC components: RCK1=270KΩ, RCK=150KΩ, CCK=150 pF DESCRIPTION C1~C3 VCC GND CK1,CK, CK 9 __ DP Dialing pulse output. This output consists of an N-channel open drain device. Normally this output will be in off state during make and on during break. Dialing pulse rate = 10pps and inter-digital pause = 800 ms when FOSC=18KHz in normal mode. Make/Break ratio select input. In normal mode, this input is used to select the Make/Break ratio: when input = VCC , M/B ratio = 1/2. when input = GND, M/B ratio = 2/3. when connected to the clock output (pin 7), this input can trigger the IN9151-3 into test mode, generating high speed dialing. 10 M/B 11 __ HK Hook switch input. This input is used to detect whether the telephone is in the On-Hook or Off-Hook state: VCC=on-hook GND=off-hook. (Resetting time = 200 ms minimum) Mute output. This output is an inverter normally at low state when there is no key entry. During outdialing it changes to high state and is used to mute the speech network. 13 MUTE IL9151-3 MAXIMUM RATINGS* Symbol VCC VIN PD Tstg TL * Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage (Referenced to GND) Power Dissipation in Still Air , Plastic DIP Storage Temperature Lead Temperature, 1mm from case for 10 seconds ** Value -0.3 to +5.5 .


IL5851 IL9151-3 IL91531


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)