DatasheetsPDF.com

HCPL2502 Dataheets PDF



Part Number HCPL2502
Manufacturers Hewlett-Packard
Logo Hewlett-Packard
Description (HCPL-xxxx) Single Channel / High Speed Optocouplers
Datasheet HCPL2502 DatasheetHCPL2502 Datasheet (PDF)

Single Channel, High Speed Optocouplers Technical Data Features • 15 kV/µs Minimum Common Mode Transient Immunity at VCM = 1500 V (4503/0453) • High Speed: 1 Mb/s • TTL Compatible • Available in 8-Pin DIP, SO-8, Widebody Packages • Open Collector Output • Guaranteed Performance from Temperature: 0°C to 70°C • Safety Approval UL Recognized – 2500 V rms for 1 minute (5000 V rms for 1 minute for HCNW and Option 020 devices) per UL1577 CSA Approved VDE 0884 Approved –VIORM = 630 V peak for HCPL-450.

  HCPL2502   HCPL2502



Document
Single Channel, High Speed Optocouplers Technical Data Features • 15 kV/µs Minimum Common Mode Transient Immunity at VCM = 1500 V (4503/0453) • High Speed: 1 Mb/s • TTL Compatible • Available in 8-Pin DIP, SO-8, Widebody Packages • Open Collector Output • Guaranteed Performance from Temperature: 0°C to 70°C • Safety Approval UL Recognized – 2500 V rms for 1 minute (5000 V rms for 1 minute for HCNW and Option 020 devices) per UL1577 CSA Approved VDE 0884 Approved –VIORM = 630 V peak for HCPL-4503#060 –VIORM = 1414 V peak for HCNW devices • Dual Channel Version Available (253X/4534/053X/ 0534) • MIL-STD-1772 Version Available (55XX/65XX/4N55) Applications w w w 6N135/6 HCNW135/6 HCNW4502/3 HCPL-2502 HCPL-0452/3 HCPL-0500/1 HCPL-4502/3 a d . s a t e h 4 t e . u m o c Description These diode-transistor optocouplers use an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input and output. Separate connections for the photodiode bias and output-transistor collector increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base-collector capacitance. Functional Diagram NC 1 ANODE 2 CATHODE 3 NC 4 8 VCC * 7 VB 6 VO 5 GND TRUTH TABLE (POSITIVE LOGIC) LED VO ON OFF LOW HIGH * NOTE: FOR 4502/3, 0452/3, PIN 7 IS NOT CONNECTED. A 0.1 µF bypass capacitor must be connected between pins 5 and 8. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. ww.DataSheet4U.com • High Voltage Insulation • Video Signal Isolation • Power Transistor Isolation in Motor Drives • Line Receivers • Feedback Element in Switched Mode Power Supplies • High Speed Logic Ground Isolation – TTL/TTL, TTL/ CMOS, TTL/LSTTL • Replaces Pulse Transformers • Replaces Slow Phototransistor Isolators • Analog Signal Ground Isolation 2 These single channel optocouplers are available in 8-Pin DIP, SO-8 and Widebody package configurations. The 6N135, HCPL-0500, and HCNW135 are for use in TTL/ CMOS, TTL/LSTTL or wide bandwidth analog applications. Current transfer ratio (CTR) for these devices is 7% minimum at IF = 16 mA. The 6N136, HCPL-2502, HCPL-0501, and HCNW136 are designed for high speed TTL/TTL applications. A standard 16 mA TTL sink current through the input LED will provide enough output current for 1 TTL load and a 5.6 kΩ pull-up resistor. CTR for these devices is 19% minimum at IF = 16 mA. The HCPL-4502, HCPL-0452, and HCNW4502 provide the electrical and switching performance of the 6N136, HCPL-0501, and HCNW136 with increased ESD protection. The HCPL-4503, HCPL-0453, and HCNW4503 are similar to the HCPL-4502, HCPL-0452, and HCNW4502 optocouplers but have increased common mode transient immunity of 15 kV/µs minimum at VCM = 1500 V guaranteed. Schematic 2 ANODE + VF CATHODE – 3 SHIELD HCPL-4503/0453 HCNW4503 IF ICC 8 VCC IO 6 VO 5 GND IB 7 * VB .


V18ZA05 HCPL2502 HCPL0452


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)