DatasheetsPDF.com

MTP5P06V Dataheets PDF



Part Number MTP5P06V
Manufacturers Motorola
Logo Motorola
Description TMOS POWER FET 5 AMPERES 60 VOLTS RDS(on) = 0.450 OHM
Datasheet MTP5P06V DatasheetMTP5P06V Datasheet (PDF)

MOTOROLA Designer's SEMICONDUCTOR TECHNICAL DATA Order this document by MTP5P06V/D TMOS V Power Field Effect Transistor TMOS V is a new technology designed to achieve an on–resistance area product about one–half that of standard MOSFETs. This new technology more than doubles the present cell density of our 50 and 60 volt TMOS devices. Just as with our TMOS E–FET designs, TMOS V is designed to withstand high energy in the avalanche and commutation modes. Designed for low voltage, high speed sw.

  MTP5P06V   MTP5P06V


Document
MOTOROLA Designer's SEMICONDUCTOR TECHNICAL DATA Order this document by MTP5P06V/D TMOS V Power Field Effect Transistor TMOS V is a new technology designed to achieve an on–resistance area product about one–half that of standard MOSFETs. This new technology more than doubles the present cell density of our 50 and 60 volt TMOS devices. Just as with our TMOS E–FET designs, TMOS V is designed to withstand high energy in the avalanche and commutation modes. Designed for low voltage, high speed switching applications in power supplies, converters and power motor controls, these devices are particularly well suited for bridge circuits where diode speed and commutating safe operating areas are critical and offer additional safety margin against unexpected voltage transients. ™ Data Sheet MTP5P06V Motorola Preferred Device P–Channel Enhancement–Mode Silicon Gate TMOS POWER FET 5 AMPERES 60 VOLTS RDS(on) = 0.450 OHM TM D New Features of TMOS V • On–resistance Area Product about One–half that of Standard MOSFETs with New Low Voltage, Low RDS(on) Technology • Faster Switching than E–FET Predecessors Features Common to TMOS V and TMOS E–FETS • Avalanche Energy Specified • IDSS and VDS(on) Specified at Elevated Temperature • Static Parameters are the Same for both TMOS V and TMOS E–FET MAXIMUM RATINGS (TC = 25°C unless otherwise noted) Rating Drain–to–Source Voltage Drain–to–Gate Voltage (RGS = 1.0 MΩ) Gate–to–Source Voltage — Continuous Gate–to–Source Voltage — Non–repetitive (tp ≤ 10 ms) Drain Current — Continuous @ 25°C Drain Current — Continuous @ 100°C Drain Current — Single Pulse (tp ≤ 10 µs) Total Power Dissipation @ TC = 25°C Derate above 25°C Operating and Storage Temperature Range Single Pulse Drain–to–Source Avalanche Energy — STARTING TJ = 25°C (VDD = 25 Vdc, VGS = 10 Vdc, PEAK IL = 5 Apk, L = 10 mH, RG = 25 Ω) Thermal Resistance — Junction to Case Thermal Resistance — Junction to Ambient G S CASE 221A–06, Style 5 TO–220AB Symbol VDSS VDGR VGS VGSM ID ID IDM PD TJ, Tstg EAS RθJC RθJA TL Value 60 60 ± 15 ± 25 5 4 18 40 0.27 – 55 to 175 125 3.75 62.5 260 Unit Vdc Vdc Vdc Vpk Adc Apk Watts W/°C °C mJ °C/W °C Maximum Lead Temperature for Soldering Purposes, 1/8″ from Case for 10 seconds Designer’s Data for “Worst Case” Conditions — The Designer’s Data Sheet permits the design of most circuits entirely from the information presented. SOA Limit curves — representing boundaries on device characteristics — are given to facilitate “worst case” design. E–FET, Designer’s and TMOS V are trademarks of Motorola, Inc. TMOS is a registered trademark of Motorola, Inc. Preferred devices are Motorola recommended choices for future use and best overall value. REV 1 TMOS © Motorola Motorola, Inc. 1996 Power MOSFET Transistor Device Data 1 MTP5P06V ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted) Characteristic OFF CHARACTERISTICS Drain–Source Breakdown Voltage (VGS = 0 Vdc, ID = 0.25 mAdc) Temperature Coefficient (Positive) Zero Gate Voltage Drain Current (VDS = 60 Vdc, VGS = 0 Vdc) (VDS = 60 Vdc, VGS = 0 Vdc, TJ = 150°C) Gate–Body Leakage Current (VGS = ± 15 Vdc, VDS = 0 Vdc) ON CHARACTERISTICS (1) Gate Threshold Voltage (VDS = VGS, ID = 250 µAdc) Threshold Temperature Coefficient (Negative) Static Drain–Source On–Resistance (VGS = 10 Vdc, ID = 2.5 Adc) Drain–Source On–Voltage (VGS = 10 Vdc, ID = 5 Adc) (VGS = 10 Vdc, ID = 2.5 Adc, TJ = 150°C) Forward Transconductance (VDS = 15 Vdc, ID = 2.5 Adc) DYNAMIC CHARACTERISTICS Input Capacitance Output Capacitance Transfer Capacitance SWITCHING CHARACTERISTICS (2) Turn–On Delay Time Rise Time Turn–Off Delay Time Fall Time Gate Charge (See Figure 8) (VDS = 48 Vdc, ID = 5 Adc, VGS = 10 Vdc) (VDD = 30 Vdc, ID = 5 Adc, VGS = 10 Vdc, RG = 9.1 Ω) td(on) tr td(off) tf QT Q1 Q2 Q3 SOURCE–DRAIN DIODE CHARACTERISTICS Forward On–Voltage (IS = 5 Adc, VGS = 0 Vdc) (IS = 5 Adc, VGS = 0 Vdc, TJ = 150°C) VSD — — trr (IS = 5 Adc, VGS = 0 Vdc, dIS/dt = 100 A/µs) Reverse Recovery Stored Charge INTERNAL PACKAGE INDUCTANCE Internal Drain Inductance (Measured from contact screw on tab to center of die) (Measured from the drain lead 0.25″ from package to center of die) Internal Source Inductance (Measured from the source lead 0.25″ from package to source bond pad) (1) Pulse Test: Pulse Width ≤ 300 µs, Duty Cycle ≤ 2%. (2) Switching characteristics are independent of operating junction temperature. LD — LS — 3.5 4.5 7.5 — — nH nH ta tb QRR — — — — 1.72 1.34 97 73 24 0.42 3.5 — — — — — µC ns Vdc — — — — — — — — 11 26 17 19 12 3.0 5.0 5.0 20 50 30 40 20 — — — nC ns (VDS = 25 Vdc, VGS = 0 Vdc, f = 1.0 MHz) Ciss Coss Crss — — — 367 140 29 510 200 60 pF VGS(th) 2.0 — RDS(on) VDS(on) — — gFS 1.5 3.6 — — — 2.7 2.6 Mhos — 2.8 4.7 0.34 4.0 — 0.45 Vdc mV/°C Ohm Vdc V(BR)DSS 60 — IDSS — — IGSS — — — — 10 100 100 nAdc — 61.2 — — Vdc mV/°C µAdc Symbol Min Typ Max Unit Reverse Recovery Time 2 Motorola TMOS Power MOSFET Transistor Device Data MTP5P06V TYPICAL ELECTRICAL CHARACTERISTIC.


MTP5P25 MTP5P06V MTP5N40E


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)