DatasheetsPDF.com

MTP2P50E Dataheets PDF



Part Number MTP2P50E
Manufacturers Motorola
Logo Motorola
Description TMOS POWER FET 2.0 AMPERES 500 VOLTS RDS
Datasheet MTP2P50E DatasheetMTP2P50E Datasheet (PDF)

MOTOROLA SEMICONDUCTOR TECHNICAL DATA Order this document by MTP2P50E/D ™ Data Sheet TMOS E-FET.™ Power Field Effect Transistor Designer's MTP2P50E Motorola Preferred Device P–Channel Enhancement–Mode Silicon Gate This high voltage MOSFET uses an advanced termination scheme to provide enhanced voltage–blocking capability without degrading performance over time. In addition, this advanced TMOS E–FET is designed to withstand high energy in the avalanche and commutation modes. The new energy e.

  MTP2P50E   MTP2P50E



Document
MOTOROLA SEMICONDUCTOR TECHNICAL DATA Order this document by MTP2P50E/D ™ Data Sheet TMOS E-FET.™ Power Field Effect Transistor Designer's MTP2P50E Motorola Preferred Device P–Channel Enhancement–Mode Silicon Gate This high voltage MOSFET uses an advanced termination scheme to provide enhanced voltage–blocking capability without degrading performance over time. In addition, this advanced TMOS E–FET is designed to withstand high energy in the avalanche and commutation modes. The new energy efficient design also offers a drain–to–source diode with a fast recovery time. Designed for high voltage, high speed switching applications in power supplies, converters and PWM motor controls, these devices are particularly well suited for bridge circuits where diode speed and commutating safe operating areas are critical and offer additional safety margin against unexpected voltage transients. • Robust High Voltage Termination • Avalanche Energy Specified • Source–to–Drain Diode Recovery Time Comparable to a Discrete Fast Recovery Diode • Diode is Characterized for Use in Bridge Circuits • IDSS and VDS(on) Specified at Elevated Temperature G S Symbol VDSS VDGR VGS VGSM ID ID IDM PD TJ, Tstg EAS RθJC RθJA TL TMOS POWER FET 2.0 AMPERES 500 VOLTS RDS(on) = 6.0 OHM ® D CASE 221A–06, Style 5 TO–220AB MAXIMUM RATINGS (TC = 25°C unless otherwise noted) Rating Drain–Source Voltage Drain–Gate Voltage (RGS = 1.0 MΩ) Gate–Source Voltage — Continuous Gate–Source Voltage — Non–Repetitive (tp ≤ 10 ms) Drain Current — Continuous Drain Current — Continuous @ 100°C Drain Current — Single Pulse (tp ≤ 10 µs) Total Power Dissipation Derate above 25°C Operating and Storage Temperature Range Single Pulse Drain–to–Source Avalanche Energy — Starting TJ = 25°C (VDD = 100 Vdc, VGS = 10 Vdc, IL = 4.0 Apk, L = 10 mH, RG = 25 Ω) Thermal Resistance — Junction to Case Thermal Resistance — Junction to Ambient Maximum Lead Temperature for Soldering Purposes, 1/8″ from case for 10 seconds Value 500 500 ± 20 ± 40 2.0 1.6 6.0 75 0.6 – 55 to 150 80 1.67 62.5 260 Unit Vdc Vdc Vdc Vpk Adc Apk Watts W/°C °C mJ °C/W °C Designer’s Data for “Worst Case” Conditions — The Designer’s Data Sheet permits the design of most circuits entirely from the information presented. SOA Limit curves — representing boundaries on device characteristics — are given to facilitate “worst case” design. E–FET and Designer’s are trademarks of Motorola, Inc. TMOS is a registered trademark of Motorola, Inc. Preferred devices are Motorola recommended choices for future use and best overall value. REV 1 TMOS © Motorola Motorola, Inc. 1995 Power MOSFET Transistor Device Data 1 MTP2P50E ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted) Characteristic OFF CHARACTERISTICS Drain–Source Breakdown Voltage (VGS = 0 Vdc, ID = 250 µAdc) Temperature Coefficient (Positive) Zero Gate Voltage Drain Current (VDS = 500 Vdc, VGS = 0 Vdc) (VDS = 500 Vdc, VGS = 0 Vdc, TJ = 125°C) Gate–Body Leakage Current (VGS = ± 20 Vdc, VDS = 0) ON CHARACTERISTICS (1) Gate Threshold Voltage (VDS = VGS, ID = 250 µAdc) Temperature Coefficient (Negative) Static Drain–Source On–Resistance (VGS = 10 Vdc, ID = 1.0 Adc) Drain–Source On–Voltage (VGS = 10 Vdc) (ID = 2.0 Adc) (ID = 1.0 Adc, TJ = 125°C) Forward Transconductance (VDS = 15 Vdc, ID = 1.0 Adc) DYNAMIC CHARACTERISTICS Input Capacitance Output Capacitance Reverse Transfer Capacitance SWITCHING CHARACTERISTICS (2) Turn–On Delay Time Rise Time Turn–Off Delay Time Fall Time Gate Charge (See Figure 8) (VDS = 400 Vdc, ID = 2.0 Adc, VGS = 10 Vdc) (VDD = 250 Vdc, ID = 2.0 Adc, VGS = 10 Vdc, RG = 9.1 Ω) td(on) tr td(off) tf QT Q1 Q2 Q3 SOURCE–DRAIN DIODE CHARACTERISTICS Forward On–Voltage (1) (IS = 2.0 Adc, VGS = 0 Vdc) (IS = 2.0 Adc, VGS = 0 Vdc, TJ = 125°C) VSD — — trr (IS = 2.0 Adc, VGS = 0 Vdc, dIS/dt = 100 A/µs) Reverse Recovery Stored Charge INTERNAL PACKAGE INDUCTANCE Internal Drain Inductance (Measured from contact screw on tab to center of die) (Measured from the drain lead 0.25″ from package to center of die) Internal Source Inductance (Measured from the source lead 0.25″ from package to source bond pad) (1) Pulse Test: Pulse Width ≤ 300 µs, Duty Cycle ≤ 2%. (2) Switching characteristics are independent of operating junction temperature. LD — — LS — 3.5 4.5 7.5 — — — nH nH ta tb QRR — — — — 2.3 1.85 223 161 62 1.92 3.5 — — — — — µC ns Vdc — — — — — — — — 12 14 21 19 19 3.7 7.9 9.9 24 28 42 38 27 — — — nC ns (VDS = 25 Vdc, VGS = 0 Vdc, f = 1.0 MHz) Ciss Coss Crss — — — 845 100 26 1183 140 52 pF VGS(th) 2.0 — RDS(on) VDS(on) — — gFS 1.5 9.5 — 2.9 14.4 12.6 — mhos — 3.0 4.0 4.5 4.0 — 6.0 Vdc mV/°C Ohm Vdc V(BR)DSS 500 — IDSS — — IGSS — — — — 10 100 100 nAdc — 564 — — Vdc mV/°C µAdc Symbol Min Typ Max Unit Reverse Recovery Time (See Figure 14) 2 Motorola TMOS Power MOSFET Transistor Device Data MTP2P50E TYPICAL ELECTRICAL CHARACTERISTICS 4 3.5 I D , DRAIN CURRENT (AMPS) 3 6V 2.5 2 1.5 1 0.5 4V 0 0 4 8 12 16 20 24 28 0 2 2.5 3 3.5 4 4.5 5 5..


4510B MTP2P50E NSR8140


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)