Document
Ordering number:ENN2624B
Monolithic Linear IC
LA6510
1A Power Operational Amplifier
Features
• High output current (IO max=1.0A). • High gain. • Equipped with current limiter pin (Adjustable by exter-
nal settings). • Supports single power source operation.
Package Dimensions
unit:mm
3046B-SIP10F
[LA6510]
25.5 24.0 3.6
3.6
16.7max 14.0 8.4
3.5 1.6 min
Specifications
Absolute Maximum Ratings at Ta = 25˚C
Parameter
Maximum supply voltage
Differential input voltage Common mode input voltage Maximum output current Allowable power dissipation Operating temperature Storage temperature
Symbol
VCC/VEE max VID
VICOM IO max Pd max
Topr
Tstg
Operating Characteristics at Ta = 25˚C, VCC/VEE=±15V
Parameter
Symbol
No-load current drain Input offset voltage Input offset current Input bias current Common mode input voltage range Common mode signal rejection ratio Maximum output voltage Voltage gain
ICCO VIO IIO IB VICM CRM VO max VGO
RS≤10kΩ RL=33Ω
1 1.32 2.54
0.5
Conditions
Conditions
10 0.45
1.3 1.6
SANYO : SIP10F
Ratings
Unit
±18 V
30 ±15 1.0 2.5 –20 to +75 –55 to +150
V V A W ˚C ˚C
Ratings min typ max
Unit
12 20 mA
2 6 mV
10 200 nA
100 700 nA
–15 +13 V
70 80
dB
±12 ±13
V
100 dB
Continued on next page.
Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other parameters) listed in products specifications of any and all SANYO products described or contained herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
42000TN (KT)/D250JK No.2624–1/3
Continued from preceding page
Parameter
Slew rate Equivalent input noise voltage Supply voltage rejection ratio Limiting current
LA6510
Symbol
Conditions
SR VNI SVRR ISC
GV=0, RL=33Ω, R=2.2Ω, C=0.1µF Rg=1kΩ, DIN AUDIO
RSC=2.2Ω
With no arbitrarily large heat sink
Tightening torque : 39N · cm
Ratings min typ max
Unit
0.15
V/µs
2 µV
30 150 µV/V
0.35
A
Allowable power dissipation, Pd max – W
Pin Assignment
With no heat sink Ambient temperature, Ta – °C
Sample Application Circuit
No.2624–2/3
LA6510
Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual propert.