DatasheetsPDF.com

74HCT9323A Dataheets PDF



Part Number 74HCT9323A
Manufacturers Philips
Logo Philips
Description Programmable ripple counter
Datasheet 74HCT9323A Datasheet74HCT9323A Datasheet (PDF)

INTEGRATED CIRCUITS 74HC/HCT9323A Programmable ripple counter with oscillator (3-State) Objective specification IC06 Data Handbook 1995 Oct 27 Philips Semiconductors Philips Semiconductors Objective specification Programmable ripple counter with oscillator (3-State) 74HC/HCT9323A FEATURES • 8-pin space saving package • Programmable 3-stage ripple counter • Suitable for over-tone crystal application up to 85MHz • 3-State output buffer • Two internal capacitors • Recommended operating rang.

  74HCT9323A   74HCT9323A



Document
INTEGRATED CIRCUITS 74HC/HCT9323A Programmable ripple counter with oscillator (3-State) Objective specification IC06 Data Handbook 1995 Oct 27 Philips Semiconductors Philips Semiconductors Objective specification Programmable ripple counter with oscillator (3-State) 74HC/HCT9323A FEATURES • 8-pin space saving package • Programmable 3-stage ripple counter • Suitable for over-tone crystal application up to 85MHz • 3-State output buffer • Two internal capacitors • Recommended operating range for use with third overtone crystals 3V to 6V (VCC = 5V"10%) DESCRIPTION The 74HC/HCT9323A are high-speed Si-gate CMOS devices. They are specified in compliance with JEDEC standard no. 7A. The HC/HCT 9323A are oscillators designed for quartz crystal combined with a programmable 3-State counter, a 3-State output buffer and an overriding asynchronous master reset (MR). With the two select inputs S1 and S2 the counter can be switched in the divide-1, 2, 4 or 8 mode. If left floating the clock is divided by 8. The oscillator is designed to operate either in the fundamental or third overtone mode depending on the crystal and external components applied. On-chip capacitors minimize external component count for third overtone crystal applications. The oscillator may be replaced by an external clock signal at input X1. In this event the other oscillator pin (X2) must be floating. The counter advances on the negative-going transition of X1. A LOW level on MR resets the counter, stops the oscillator and sets the output buffer in the 3-State condition. MR can be left floating since an internal pull-up resistor will make the MR inactive. In the HCT version, the MR input and the two mode select pins S1 and S2 are TTL compatible, but the X1 input has CMOS input switching levels and may be driven by a TTL output using a pull-up resistor connected to VCC. • Oscillator stop function (MR) • Output capability: • ICC category: MSI bus driver ³ (15 LSTTL) APPLICATIONS • Control counters • Timers • Frequency dividers • Time-delay circuits • CIO (Compact Integrated Oscillator) • Third-overtone crystal operation QUICK REFERENCE DATA GND = 0V; Tamb = 25°C, tr = tf = 6ns SYMBOL PARAMETER CONDITIONS Tamb = 25°C; GND = 0V HC TYPICAL HCT 8 150 3.5 UNIT tPLH tPHL fmax CI CPD Propagation delay X1 to OUT (S1 = S2 = LOW) Maximum clock frequency Input capacitance except X1 and X2 Power dissipation capacitance per package CL = 50pF; VCC = 5V 8 150 3.5 ns MHz pF pF NOTES: CPD is used to determine the dynamic power dissipation (PD in µW): = (CPD VCC2 fI) + (CL + VCC2 fO) + (Ipull-up VCC) PD where: = inputfrequency in MHz.. fI = output frequency in MHz. fO VCC = Supply voltage in V. = Output load capacitance in pF. CL Ipull-up = Pull-up currents in µA. For HC and HCT an external clock is applied to X1 with: tr = tf v 6ns, VI is GND to VCC, MR = HIGH. Ipull-up is the summation of –II (µA) of S1 and S2 inputs at the LOW state. ORDERING INFORMATION PACKAGES 8-Pin Plastic SO TEMPERATURE RANGE 0°C to +70°C ORDER NUMBER 74HC/HCT9323A D DWG NUMBER SOT96-1 1995 Oct 27 2 Philips Semiconductors Objective specification Programmable ripple counter with oscillator (3-State) 74HC/HCT9323A PIN CONFIGURATION IEC LOGIC SYMBOL 6 X2 CP MR CD 3 2 S1 S2 OUT 1 OUT S2 S1 GND 1 2 3 4 8 7 6 5 VCC X1 X2 MR 7 5 X1 SK00013 SK00014 PIN DESCRIPTION PIN NUMBER 1 3, 2 4 5 6 7 8 SYMBOL OUT S1-S2 GND MR X2 X1 VCC FUNCTION Counter output Mode select inputs for divide by 1, 2, 4 or 8 Ground (0V) Master reset (active LOW) Oscillator pin Clock input/oscillator pin Positive supply voltage FUNCTION TABLE INPUTS S1 0 0 1 1 S2 0 1 0 1 OUTPUTS OUT fI fI/2 fI/4 fI/8 FUNCTIONAL DIAGRAM 6 X2 7 X1 CP 5 MR CD S1 S2 OUT 3-STAGE BINARY COUNTER AND DECODER 3 2 1 SK00015 1995 Oct 27 3 Philips Semiconductors Objective specification Programmable ripple counter with oscillator (3-State) 74HC/HCT9323A LOGIC DIAGRAM X2 X1 CP 2pF VCC FF 2pF VCC Q CP FF Q CP FF Q R R R DECODER VCC VCC MR VCC OUT Internal capacitors typical 2pF each, including stray capacitors on pins X1 and X2, total capacitance will be typical 7pF per pin SK00016 1995 Oct 27 4 Philips Semiconductors Objective specification Programmable ripple counter with oscillator (3-State) 74HC/HCT9323A SO8: plastic small outline package; 8 leads; body width 3.9mm SOT96-1 1995 Oct 27 5 Philips Semiconductors Objective specification Programmable ripple counter with oscillator (3-State) 74HC/HCT9323A DEFINITIONS Data Sheet Identification Objective Specification Product Status Formative or in Design Definition This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible.


74HCT93 74HCT9323A 74LCX00


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)